Go to homepage

Blackmagic

Blackmagic


Filter
Chaos Cable Ties
Chaos Cable Ties
Chaos Cable Ties Adjustable Cable Ties With Multiple Mounts.One of the little things that makes life easier on setSet with 12 pcs "Chaos Cable Ties"4x 1/4" thread4x 3/8" thread 4x stickytapeOrganize your cables on your camera set with our Chaos Cable Ties. These adjustable, reusable ties are great for managing cable on set. they also reduce cable strain as they keep the cable from sliding through unlike other ties.  The set comes with 4 ties that have a 3/8th thread and 4 that have 1/4-20 thread to attached to cages and organize cables around the camera they way you want. Because of the thread, you can use them again and again. No threaded mount points available? Chrosziel has you covered with 4 adhesive Chaos Cable Ties in the set. 
Chrosziel QuickLock V-Mount Tripod Plate
Chrosziel QuickLock V-Mount Tripod Plate
Chrosziel QuickLock V-Mount Tripod Plate Chrosziel QuickLock Tripod Plate for cameras with V-mount, fully adjustable 3/8" + 1/4" mount threads. Ultra-lightweight made of aircraft-grade aluminium, quiet, low-noise locking mechanism, play-free mounting of the camera by push and pull release/lock lever.  (replaces 401-130)FEATRURESSecure, Play-Free Camera MountingLow-Noise Locking Mechanism For all cameras with V Mount Play-Free mounting on the Tripod PlateThe  QuickLock Plate 401-150 locking mechanism consists of three parts: movable unlocking bolt at the front,fork-shaped locking slide in the middleretractable locking bolt at the rearTo attach a camera with V-mount adapter to the QuickLock Plate, push it into the V-shaped notch on the front and pull the locking lever to the right. The following happens: Unlocking bolt  and locking slide  move forwards / left, the locking bolt downwards. Compared to average standard Quick Release Plates or VCT Tripod Plates (mostly without retractable locking bolts), the Chrosziel locking mechanism with retractable locking bolt has play-freely clamps to secure even worn out rear mounting mechanisms located on the bottom of the camera. For cine cameras equipped only with tripod screw threads at the bottom , a Chrosziel lightweight support (such as 401-EVA1) enables mounting the camera security to the quick release plate. For ENG cameras, rod support can be added via a Chrosziel lightweight support (like 401-50 for Sony) in combination with the QuickLock Plate.
DV StudioRig follow focus with gear drive a. FlexiGearRing
DV StudioRig follow focus with gear drive a. FlexiGearRing
DV StudioRig follow focus with gear drive a. FlexiGearRing DV StudioRig follow focus with gear drive 0.8 (206-12 and FlexiGearRing (206-30), scale (205-02), for one-side-operation. For lens diameters up to 110 mm.
DV StudioRig Kit in Case, Follow Focus with all gears
DV StudioRig Kit in Case, Follow Focus with all gears
DV StudioRig Kit in Case, Follow Focus with all gears DV StudioRig plus complete Kit with six gear drives in Case. Consisting of: 206-60S follow focus w. VariLock handwheel, 205-02 scale and gear drives: 206-12, 206-13, 206-14, 206-15, 206-16, 206-17 in Case
DV StudioRig, follow focus
DV StudioRig, follow focus
DV StudioRig, follow focus DV StudioRig, follow focus incl. scale (205-02), for one-side-operation. For lens diameter max. 115 mm measured with gear drive 206-12 (not included). Precise gears with practically no play at a very affordable price. A single lock for rod and extension clamp makes changing of lenses quick. Hand wheel with fine-structured surface for save grip. The scale is easy to change and the reference marking is adjustable for the operator or the assistant. Gear drives and gear rings for the different lenses ensure precise adjustments and can be mounted without tool on both sides of the gear unit
Flexi-Insertring 110:50/85mm
Flexi-Insertring 110:50/85mm
Flexi-Insertring 110:50/85mm Flexi-Insert-Ring, for 110mm screw-in, e.g. MB450. Light protection for lens diameters between 50 and 85 mm.
Flexi-Insertring 110:75/98mm
Flexi-Insertring 110:75/98mm
Flexi-Insertring 110:75/98mm Flexi-Insert-Ring, for 110 mm screw-in, e.g. MB450. Light protection for lens diameters between 75 and 98 mm
Flexi-Insertring Ø 130 clamp-on
Flexi-Insertring Ø 130 clamp-on
Flexi-Insertring Ø 130 clamp-on Flexi-Insertring for clamp-on-mount Ø 130mm for lens diameter 95 to 125mm. Accessory for MB 456 Academy on rods.
Focus Drive for 206-05S + 206-60S mod 0.8, Ø 36,8mm
Focus Drive for 206-05S + 206-60S mod 0.8, Ø 36,8mm
Focus Drive for 206-05S + 206-60S mod 0.8, Ø 36,8mm Focus drive (for 206-05S + 206-60S), mod 0.8, for gear rings and Canon and Fujinon cine style lenses, Ø 36.8mm, 44 teeth.
Focus Drive mod 0.8, 46mm
Focus Drive mod 0.8, 46mm
Focus Drive mod 0.8, 46mm Focus drive (DV StudioRig / plus) for DigiPrimes + Movie Lenses, mod 0.8, Ø 46mm, 56 teeth.
Handle Bar proVideo plus
Handle Bar proVideo plus
Handle Bar proVideo plus Handle Bar plus proVideo (w. 220mm), for use with LWS. With clamp forØ 15mm rods
Light Weight Support 15 HD BlackMagic Cinema and Studio
Light Weight Support 15 HD BlackMagic Cinema and Studio
Light Weight Support 15 HD BlackMagic Cinema and Studio LWS - Light Weight Support 15 HD BlackMagic Cinema and Production, with Ø 15 mm rods L. 310 mm w. thread for extensions, double rod guidance and clamp
Light Weight Support 15 HD for DSLR cameras
Light Weight Support 15 HD for DSLR cameras
Light Weight Support 15 HD for DSLR cameras LWS - Light Weight Support 15 HD for DSLR cameras with anti-twist block, w. Ø 15 mm rods L. 310 mm, double rod guidance and clamps. Adjustable for larger camera bodies by removing spacers. Shorter M5 x 45 mm screws and Allen wrench are included. (Compatible for Canon EOS 5D, Nikon D800, Nikon D90, Panasonic DMC-GH3, DMC-GH4, Black Magic Pocket Camera)
LWS 15 HD Allround
LWS 15 HD Allround
LWS 15 HD Allround LWS - Light Weight Support 15 HD Allround, w. Ø 15mm rods L. 310mm, double rod guidance and clamp, adjustable for any camera with optical height betw. 26.5 a. 72.5mm (distance betw. lens center and camera bottom). Spacers (pairs) of 1, 2, 4, 8, 2 x 16mm, set of screws, table with camera heights and Allen wrench are included. (All Chrosziel camera platforms of series 401-4xx may be used alternatively.)Adjustable for any camera with optical height betw. 26.5 a. 72.5mm (distance betw. lens center and camera bottom) For e.g.: Sony PMW-F3, F5/F55, FS 100/FS 700, Canon EOS C100/C300/C500 Ø 15mm rods, length 310mm, double rod guidance and clamp
MatteBox 450R2, w. Double-Rotating-Filter Stage, dia.114/110
MatteBox 450R2, w. Double-Rotating-Filter Stage, dia.114/110 MatteBox 450R2, with Double-Rotating-Filter Stage, incl. mask 16:9, french flag (450-11), pivot mechanism for side wings, 2 rotating filterholders 4x4 (402-12) and multiformat 4x4/4x5.650 (410-04), rod clamping for Ø15mm rods, end plate Ø114/110mm
MatteBox MB 450W Super Wide
MatteBox MB 450W Super Wide
MatteBox MB 450W Super Wide MatteBox 450W Super Wide MatteBox for wide-angle lenses, with Double-Rotating Filter Stage, incl. french flag (450-11), 2 filterholders multiformat 4x4/4x5.650 (410-31), bracket for Ø15mm rods, clamp adapter Ø130mm
MultiPad 15
MultiPad 15
MultiPad 15 MultiPad 15 Adjustable ShoulderPad complete with MultiPad 15 Straight and Side Lock for use with Ø 15 mm rods. Pad mounts under the camera, behind or sidewards for cameras with viewfinder in the body.
QuickFit Lens support for dia. 15 +19 mm rods
QuickFit Lens support for dia. 15 +19 mm rods
QuickFit Lens support for dia. 15 +19 mm rods Universal 15 + 19mm Lens Support Bracket with 3 support stands, intercombinable, lenght 14, 27 and 35 mm, for lenses w. 1/4" + 3/8" threads. With QuickFit device for Ø15 + 19mm rods.
Step-down Ring Ø 130:114mm
Step-down Ring Ø 130:114mm
Step-down Ring Ø 130:114mm Step-down Ring Ø 130:114mm
Universal Lens support, Quick-fit for Ø 15mm rods
Universal Lens support, Quick-fit for Ø 15mm rods
Universal Lens support, Quick-fit for Ø 15mm rods Lens Support Bracket 15 Universal with two support stands with length 14 and 27 mm, combinable for all lenses with 1/4" and 3/8" threads. With QuickFit device for Ø 15mm rods.
Zoomer the Universal Zoom Servo Drive
Zoomer the Universal Zoom Servo Drive
Zoomer the Universal Zoom Servo Drive Chrosziel has expanded the successful CDM Zoom Servo Drive family. The Zoomer is a compact and universal zoom motor that can be pivoted to almost any lens by simply mounting it on a 15mm rod. The universal motor unit CDM-UNI-Z2 fits seamlessly into the operating functions of the Sony cameras of the FX9 / FX6 / FS7 / FS5 series. The servo drive is controlled via the zoom rocker on the handle. The motor control can be addressed via Sony's camera-specific protocol and also works independently of the camera signals when a LANC zoom rocker is plugged directly into the servo.Due to the included Chrosziel Flexi toothed ring (#206-30), the Zoomer can be used with almost any zoom lens even without toothing. The multi-function handgrip, which in addition to the recording function and a zoom rocker also provide control over the camera menu and other freely selectable functions, are extremely popular on current video cameras with large sensors and are indispensable for effective operation. The Chrosziel Universal Zoom Servo Drive now allows optimal use of all manual zoom lenses together with the multi-function handgrip. For this purpose, the Zoomer is slid onto a 15mm rod and swiveled onto the zoom lens. Two plug-in cables establish the connection with the camera. One cable is used for the power supply from the camera battery, the second for the connection to the control commands between the handle and the camera. When using a standard LANC zoom rocker or handle with the Sony PXW-FS5, PXW-FS7 and PXW-FS7II, the servo is connected between the handle and the camera via an input and an output jack to receive all zoom control signals. For setup with the Sony PXW-FX9 camera, a Y-cable is used that accepts the Sony multi-connector and connects to both the input jack of the Zoomer and the input jack of the camera. For the Sony ILME-FX6 camera, a Y-cable is used and connects the 3.5mm connector of the Sony handgrip, input jack of the Universal Zoom Servo Drive, and the Sony camera.  FEATURESUniversal zoom motor The Zoomer is a compact and universal zoom motor that can be pivoted to almost any lens by simply mounting it on a 15mm rod. Controlled via Sony and LANC handgrip The Sony FX6 / FX9 / FS5 / FS7 handgrip zoom rocker controls directly the servo drive unit. Other zoom rocker with LANC protocol are compatible too, e.g. mounted handgrip. Camera control signals forwarded Control commands are immediately looped through to the camera (e.g. menu / user buttons / focus magnification / camera run & stop). Panasonic DC-BS1H & DC-BGH1 box cameras A recent firmware updated has made the CDM-UNI-Z2 compatible with the Panasonic BS1H and BGH-1 box cinema cameras when used with a Manfrotto MVR901EPLA and MVR901ECLA control handles as well as the Libec ZFC-L and ZC-LP zoom controllers. Technical dataPower supply 10-30V (Lemo compatible 0B 5-pin) 2.5mm socket (control command In) 3.5mm socket (control command In&Out)USB Type min A-B (firmware updates) Torque 0.5Nm Power consumption max. approx. 350mAh @ 12VIN THE BOX 1x CDM-UNI-Z2 Digital motor unit 1x LANC cable 1x LANC extension cable 1x MN-AB-A90 (power supply cable 12 Volt A/B D-Tap – angled 90° rotated 0B 5pin) 1x 206-30 Flexi Gear Ring (Ø 60-120mm) 1x Gear Drive, mod. 0.8 (Ø 40mm) 1x CAB-FX9 for Sony PXW-FX9 compatibility 1x CAB-FX6 for Sony PXW-FX6 compatibility USB Mini AdapterSign up for ZOOMER email updatesDon't miss future news about the ZOOMER and subscribe to the Zoomer Email list. Yes, keep me updated about the ZOOMER and send me future news about it.NOTE: we will not use your email for any other emails not related to the Zoomer.
This website uses cookies to ensure the best experience possible. More information...