Go to homepage

Sony PXW-FS7 MKII

Sony PXW-FS7 MKII


Filter
Bridge Plate DigiCine, Ø19mm
Bridge Plate DigiCine, Ø19mm
Bridge Plate DigiCine, Ø19mm Bridge Plate with Ø19mm rods, L= 440mm, for Sony F23, F35, F55, F65, Phantom Flex and with LWS as adaptor for Red Epic / Scarlet, Canon EOS C Series and other
Bridge Plate incl. Ø19mm Rods
Bridge Plate incl. Ø19mm Rods
Bridge Plate incl. Ø19mm Rods Bridge Plate incl. Ø19mm Rods, l. 440mm (for combination with QuickLock Tripod Plates 401-120/401-130 )
Tip
CDM-MK-Z2
CDM-MK-Z2
CDM-MK-Z2 CDM-MK-Z2 - compact control-unit for Fujinon Zoom MK 18-55, 50-135mm for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7) or LANC zoom devices. Incl. 1x digital servo-motor-unit, 1x LANC cable, 1x LANC extension cable, 1 x MN-AB (powercable 12 Volt A/B D-Tap 0B 5pin), 1x Allen Key, 1x Mini-USB-adapter.DESIGNED FOR FUJINON MK 18-55MM T2.9 & FUJINON MK 50-135MM T2.9 CONTROLLED VIA SONY FS & LANC HANDGRIP Control directly the zoom servo drive via optically de-coupled LANC sockets and Sony FS5 / FS7 handgrip zoom rocker. Other zoom rockers with LANC protocol are compatible too, e.g. mounted to handgrip. CAMERA CONTROL SIGNALS FORWARDED Control signals (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera. SINGLE UNIT MOUNTED ONTO LENS Two captive screws keeping the single servo drive unit permanently fixed onto lens. 4 ZOOM MODES 1st EB / Documentary, 2nd Live / Hardcut, 3rd Silent, 4th Direct Mode
CDM-XK-Z2
CDM-XK-Z2
CDM-XK-Z2 CDM-MK-Z2 - servo drive unit for Fujinon Zoom XK 20-120mm for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7) or LANC zoom devices. ZOOM SERVO DRIVE FOR FUJINON XK ZOOM LENS: CDM-XK-Z MOTORIZE YOUR FUJINON XK6X20 20-120MM T3.5 WITH CHROSZIEL SINGLE UNIT MOUNTED ONTO LENSTwo captive screws keeping the single servo drive unit permanently fixed onto lens.CONTROLLED VIA SONY FS & LANC HANDGRIPThe Sony FS5 / FS7 handgrip zoom rocker controls directly the servo drive unit. Other zoom rockers with LANC protocol are compatible too, e.g. mounted to handgrip.CAMERA CONTROL SIGNALS FORWARDEDControl signals (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera.4 ZOOM MODESEB / Documentary, Live / Hardcut, Silent, Direct Mode_________________________________________________________________All in one single housing Developed for the Fujinon XK6x20 20-120 mm zoom lens the CDM-XK-Z enables ways of creativity that may be impossible just by zooming manually. To simplify the operator’s workflow the zoom servo drive is directly mounted onto the lens by two captive screws. The weight of the CDM-XK-Z including digital motor, gear, PCB with CPU, screws and cabling is 0.44 lbs. (197 gram). With the zoom servo drive Chrosziel addresses camera operators who are working in the broadcast and documentary sector looking for a reasonably priced zoom servo drive. _____________________________________________________All camera control signals forwarded Control commands (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera via the LANC protocol. By using a Sony PXW-FS5 or a Sony PXW-FS7 camera with a SWIT battery a D-Tap to a (straight or angled) Lemo compatible 5-Pin power cable is used (Chrosziel order numbers: MN-AB-A with angled Lemo compatible socket / MN-AB with straight Lemo compatible socket). The two Jack-Jack cables are forwarding the control commands from the hand grip. If e.g. a Panasonic Varicam, Sony PMW-F5 or Sony PMW-F55 are used a combined cable with power and start / stop is required, like a Hirose 4-Pin to a (straight or angled) Lemo compatible 5-Pin cable (Chrosziel order numbers: F55-A2-PCAM-A with angled Lemo socket / F55-A2-PCAM with straight Lemo compatible socket). Also, the two Jack-Jack cables are forwarding the control commands from the hand grip. Also, Chrosziel offers a variety of power cables with straight and angled plugs for all types of camera power out sockets and batteries including camera run / stop functionality. _____________________________________________________Chrosziel CDM-XK-Z Zoom Servo Motor: zoom modes For freedom of creativity the operator may choose from four different zoom modes: EB / Documentary Mode, Live / Hardcut Mode, Silent, and Direct Mode. EB / Documentary ModeDesigned for long and smooth zoom drives with the CDM-LWZ3-Z it offers slow creeping zoom transitions while keeping the motive perfectly framed.Silent ModeTo reduce the sound of the zoom servo drive the maximum speed of its motor is limited to 40 percent making the setup almost inaudible.Live / Hardcut ModeTo catch the best moments, the Live / Hardcut Mode is useful. It uses 80 percent of the maximum speed capacity of the motor offering fast zoom drives but with Soft Ramping.Direct ModeThe Direct Mode finally uses the full speed capacity of the Zoom Servo Drive. The LANC commands are implemented instantaneously without ramping and smooth transitions. Useful for B camera operators catching snaps shots from the concert.______________________________________________________________How to change zoom modes You can choose the different modes by pressing the zoom rocker for round about 25 seconds, then the green LED flashes very fast while changing the zoom mode and after that it blinks 1, 2, 3 or 4 times* – depends on the zoom mode you chose (* 1 = EB / Documentary / 2 = Silent / 3 = Live / Hard Cut / 4 = Direct). To cycle through these all you need to do is hold the zoom rocker down one way for a couple of seconds to switch to the next mode, and the other way, hold to reverse.
Chrosziel QuickLock V-Mount Tripod Plate
Chrosziel QuickLock V-Mount Tripod Plate
Chrosziel QuickLock V-Mount Tripod Plate Chrosziel QuickLock VCT Tripod Plate for cameras with V-mount, fully adjustable 3/8" + 1/4" mount threads. Ultra-lightweight made of aircraft-grade aluminium, quiet, low-noise locking mechanism, play-free mounting of the camera by push and pull release/lock lever.  (replaces 401-130)FEATRURESSecure, Play-Free Camera MountingLow-Noise Locking Mechanism For all cameras with V Mount Play-Free mounting on the Tripod PlateThe  QuickLock Plate 401-150 locking mechanism consists of three parts: movable unlocking bolt at the front,fork-shaped locking slide in the middleretractable locking bolt at the rearTo attach a camera with V-mount adapter to the QuickLock Plate, push it into the V-shaped notch on the front and pull the locking lever to the right. The following happens: Unlocking bolt  and locking slide  move forwards / left, the locking bolt downwards. Compared to average standard Quick Release Plates or VCT Tripod Plates (mostly without retractable locking bolts), the Chrosziel locking mechanism with retractable locking bolt has play-freely clamps to secure even worn out rear mounting mechanisms located on the bottom of the camera. For cine cameras equipped only with tripod screw threads at the bottom , a Chrosziel lightweight support (such as 401-EVA1) enables mounting the camera security to the quick release plate. For ENG cameras, rod support can be added via a Chrosziel lightweight support (like 401-50 for Sony) in combination with the QuickLock Plate.
DV StudioRig follow focus with gear drive a. FlexiGearRing
DV StudioRig follow focus with gear drive a. FlexiGearRing
DV StudioRig follow focus with gear drive a. FlexiGearRing DV StudioRig follow focus with gear drive 0.8 (206-12 and FlexiGearRing (206-30), scale (205-02), for one-side-operation. For lens diameters up to 110 mm.
DV StudioRig Kit in Case, Follow Focus with all gears
DV StudioRig Kit in Case, Follow Focus with all gears
DV StudioRig Kit in Case, Follow Focus with all gears DV StudioRig plus complete Kit with six gear drives in Case. Consisting of: 206-60S follow focus w. VariLock handwheel, 205-02 scale and gear drives: 206-12, 206-13, 206-14, 206-15, 206-16, 206-17 in Case
DV StudioRig, follow focus
DV StudioRig, follow focus
DV StudioRig, follow focus DV StudioRig, follow focus incl. scale (205-02), for one-side-operation. For lens diameter max. 115 mm measured with gear drive 206-12 (not included). Precise gears with practically no play at a very affordable price. A single lock for rod and extension clamp makes changing of lenses quick. Hand wheel with fine-structured surface for save grip. The scale is easy to change and the reference marking is adjustable for the operator or the assistant. Gear drives and gear rings for the different lenses ensure precise adjustments and can be mounted without tool on both sides of the gear unit
Flexi-Insertring Ø 130 clamp-on
Flexi-Insertring Ø 130 clamp-on
Flexi-Insertring Ø 130 clamp-on Flexi-Insertring for clamp-on-mount Ø 130mm for lens diameter 95 to 125mm. Accessory for MB 456 Academy on rods.
Focus Drive for 206-05S + 206-60S mod 0.8, Ø 36,8mm
Focus Drive for 206-05S + 206-60S mod 0.8, Ø 36,8mm
Focus Drive for 206-05S + 206-60S mod 0.8, Ø 36,8mm Focus drive (for 206-05S + 206-60S), mod 0.8, for gear rings and Canon and Fujinon cine style lenses, Ø 36.8mm, 44 teeth.
Focus Drive mod 0.8, 46mm
Focus Drive mod 0.8, 46mm
Focus Drive mod 0.8, 46mm Focus drive (DV StudioRig / plus) for DigiPrimes + Movie Lenses, mod 0.8, Ø 46mm, 56 teeth.
Lensport Iris Motor for cine lenses and Hirose 12pin output cameras
Lensport Iris Motor for cine lenses and Hirose 12pin output cameras
Lensport Iris Motor for cine lenses and Hirose 12pin output cameras Universal Lensport Iris Motor for cine lenses in Broadcast / ENG Run& Gun setups The universal Iris Motor is a compact and universal Iris motor that can be pivoted to almost any lens by simply mounting it on a 15mm rod. The universal motor unit CDM-LP-I fits seamlessly into the operating functions of any camera with Hirose 12pin lensport communcation. The servo drive is controlled via the 12pin Hirose output of the camera. The motor control can be addressed via the camera-specific Broadcast protocol and also works in conjunction with e.g. the MetaMount E-to-PL adapter.The Chrosziel Lensport Iris Motor now allows optimal use of all manual zoom and prime lenses together with any camera with Hirose 12pin output. For this purpose, the Iris motor is slid onto a 15mm rod and swiveled onto the zoom or prime lens. The curled Hirose 12pin cable establish the connection with the camera. Compatibility: The Universal Iris Motor has been successfully tested with the following cameras (manual and automatic iris control): ARRI Amira Blackmagic URSA Broadcast G2 & URSA Mini Pro 12K Canon C300/500 with EU-V2 expansion unit Panasonic AK-PLV100 Sony F5/F55 with LA-FZB1 adapter Sony Venice Sony E-Mount cameras with Chrosziel MetaMount MA-EPL-HR12 Manual Passive Mode: For temporary manual control, the motor can be set to passive mode. Simply press the motor button once briefly and the motor can be rotated freely. Once the button is pressed again, the motor is back in Active mode and controlled by the camera. Metadata:For setup, the cable is connected to the Hirose 12pin socket of the camera. The motor automatically calibrates itself and finds the endstops of the lens. For metadata calibration, the motor needs to learn T-Stop 4 and 16. With the press of the only button, the motor goes into passive mode and the user can turn the motor without resistance. The motor is turned to T-Stop 4 and the the press of the button confirms the position. Afterwards the motor is turned to T-Stop 16 and the position is confirmed with another press of the button. Ready! FEATURESUniversal Iris motor The Iris Motor is a compact and universal Iris motor that can be pivoted to almost any lens by simply mounting it on a 15mm rod. Controlled via any Hirose 12pin camera outputThe camera's Hirose 12pin Lensport output controls directly the Iris motor unit. Remote Iris and AutoIris controlUse the Iris motor in a remote setup and control it via the RCP or WebGUI of any camera with Hirose 12pin connector. Or switch on the AutoIris functionality of your camera and the camera uses the Chrosziel Univeral Iris Motor for AutoIris control.
MatteBox MB 450W Super Wide
MatteBox MB 450W Super Wide
MatteBox MB 450W Super Wide MatteBox 450W Super Wide MatteBox  for Wide-Angle lenses, with double-rotating Filter Stages The Chrosziel MB 450W Super Wide Matte Box is a lightweight, yet robust, carbon fiber matte box for professional cinema and video cameras. The "Super Wide" design allows for full frame lenses as wide as 20mm to be used. 1/3"-chip camcorders can use as wide as 2.6mm focal length setting without vignetting. 1/2"-chip camcorders can use down to 3.6mm. Use the included top flag to control glare and reflections for improved contrast and reduced ghosting in the recorded image. Further control can be achieved through separately available side and bottom flags.Both filter stages accept 4x4" and 4x5.65" filters and rotate for use and control of polarizing as well as graduated filters. To use this matte box on your camera, the camera must be mounted on a separately available 15mm LWS baseplate. Fit the matte box on the rods until it covers the lens front. Rod-mounted matte boxes are preferred over clamp-on matte boxes in many production situations as they are always properly aligned with the image horizon.What's In The Box: MB450W MatteBox  French flag (450-11)2 filter holders multiformat 4x4/4x5.650 (410-31), bracket for Ø15mm rodsclamp adapter Ø130mm
MatteBox MB 456 Academy Double
MatteBox MB 456 Academy Double
MatteBox MB 456 Academy Double The Chrosziel Matte Box 456-20 Academy (2 Filter Holders) consists of a 456-R20 matte box, French flag, a filter stage for two individually rotating filter holders, two 4 x 5.65"/5 x 5" filter holders, a 130mm clamp-on rear plate, and a bracket for 15mm lightweight support rods. It is ideal for use with handheld and studio production cameras.The 456-R20 Matte Box offers a wide angle (16:9/4:3) housing for lenses as wide as 12mm (35mm Academy) and eliminates the effects of vignetting. Equipped with a filter stage for two independently rotating 4 x 5.65"/5 x 5" filter holders, the matte box provides sufficient space for adjusting the position of filters.Provided with a French flag, the Matte Box 456-20 Academy controls the angle of light and eliminates lens glare and flare. It can be coupled with optional side wings for accurate light adjustment. The kit includes a 130mm clamp-on rear plate and a bracket for use with 15mm lightweight support rods (optional).With optional bridge plate adapters, you can interface the kit with 15 or 19mm bridge plate rods. An optional swing-away bracket, attached to the back of the matte box housing, allows for quick and efficient lens changes.What's in the Box: Matte Box 456 Academy Double, for full frame cameras, with Double-Rotating Filter StageFrench flag (402-26)2 filter holders multiformat 5x5/4x5.650 (510-01)16:9 (416-03) matte insertBracket for Ø15mm rods and clamp adaptor Ø130mm
Mount Adapter E-to-PL with built-in electronics for lens meta data
Mount Adapter E-to-PL with built-in electronics for lens meta data
Mount Adapter E-to-PL with built-in electronics for lens meta data The Chrosziel Meta Mount is a Sony E camera to PL lens “hot mount” adapter with metadata communication. Each mount has the required pin contacts necessary to transmit lens metadata through to the camera and conversely the contacts provide lens control through a 12-pin Hirose out connection to an ENG lens. When the Meta Mount is used with cine lenses with LDS or Cooke/i Data the metadata such as iris setting, focus distance and zoom focal length are transmitted through the adapter and appear in the viewfinder, on the monitor and are recorded in the video file for use in post processing. When the Meta Mount is used with an ENG servo motor-controlled broadcast lens the Focus/Iris/Zoom servo’s can be controlled through the camera and are compatible with the Sony FX9 / FX6 / FX3 hand grips, RCP or camera’s web GUI. This allows for easy and full control of an ENG broadcast lens through a Sony E mount camera. The Meta Mount is shimmable with the included shim set for the E-mount.Key Features: ·        Sony E Mount Camera to PL mount Lens ·        Electronic contacts for metadata communication and lens control ·        Lens metadata displayed in camera and recorded to file ·        Shimmable E Mount ·        Full focus/Iris/Zoom control on servo motor ENG lenses Technical data: - E Mount camera to PL mount lens - Contact and electronics for Metadata communication - 12-pin Hirose out for ENG lens control - 3/8th lens support socket - USB Type min A-B (for firmware updates only) - Power supply 10-16V (Lemo compatible 0B 5-pin) - Power consumption max. ca. 350mAh @ 12V - Part number MA-EPL-HR12 - EAN number: 4250618846934 In the box: - 1x Meta Mount E-to-PL adapter (MA-EPL-HR12) - 1x MN-AB (power supply cable 12 Volt A/B D-Tap – 0B 5-pin Lemo) - 1x F55-A2-P-CAM - 1x Shim Set, E-Mount side - 1x USB Mini Adapter Sign up for META MOUNT email updatesDon't miss future news about the META MOUNT and subscribe to the META MOUNT Email list. Yes, keep me updated about the META MOUNT and send me future news about it.NOTE: we will not use your email for any other emails not related to the Meta Mount.
Power Cable CDM-XXX-Z angle 90 Sony
Power Cable CDM-XXX-Z angle 90 Sony
Power Cable CDM-XXX-Z angle 90 Sony Power cable for CDM-XXX-Z Zoom motor from cameras Sony F55, FS7, XDCA, BP-U60T a. Panasonic Varicam, HRS 4pin 12V Lemo 0B 5pin angled 90 degree towards cam, (reduce motor performance, low power!)
QuickFit Lens support for dia. 15 +19 mm rods
QuickFit Lens support for dia. 15 +19 mm rods
QuickFit Lens support for dia. 15 +19 mm rods Universal 15 + 19mm Lens Support Bracket with 3 support stands, intercombinable, lenght 14, 27 and 35 mm, for lenses w. 1/4" + 3/8" threads. With QuickFit device for Ø15 + 19mm rods.
Rear Rod Clamp for Light Weight Support
Rear Rod Clamp for Light Weight Support
Rear Rod Clamp for Light Weight Support Rear Rod Clamp for Light Weight Support, ideally suited for: 401-FX9401-FX6401-FS7401-FS5401-C70401-C500II401-C300III401-C700 Light Weight Supports.INCLUDED IN BOX1x Rear Rod Clamp for Light Weight SupportOne Pair of Steel Rods: Diameter: 15mm, Length: 100mm
Step-down Ring Ø 130:114mm for MB456, MB450 and SD412
Step-down Ring Ø 130:114mm for MB456, MB450 and SD412
Step-down Ring Ø 130:114mm for MB456, MB450 and SD412 Step-down Ring Ø 130:114mm For Chrosziel 450W-20, 456-20 & 456-30 Matte Boxes and SD412 (412-02F130 only) Sunshade, and for Use with Zeiss Compact Prime, Sony PL-Mount Prime & Angenieux Optimo DP Rouge Zoom Lenses
Universal Lens support, Quick-fit for Ø 15mm rods
Universal Lens support, Quick-fit for Ø 15mm rods
Universal Lens support, Quick-fit for Ø 15mm rods Lens Support Bracket 15 Universal with two support stands with length 14 and 27 mm, combinable for all lenses with 1/4" and 3/8" threads. With QuickFit device for Ø 15mm rods.
ZOOM SERVO DRIVE FOR ZEISS LIGHTWEIGHT ZOOM LWZ3 21-100 MM – VERSION II
ZOOM SERVO DRIVE FOR ZEISS LIGHTWEIGHT ZOOM LWZ3 21-100 MM – VERSION II
ZOOM SERVO DRIVE FOR ZEISS LIGHTWEIGHT ZOOM LWZ3 21-100 MM – VERSION II CDM-LWZ3-Z2 - compact control-unit for Zeiss Zoom LWZ.3 21-100mm for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7) or LANC zoom devices. Incl. 1x digital servo-motor-unit, 1x LANC cable, 1x LANC extension cable, 1 x MN-AB (powercable 12 Volt A/B D-Tap 0B 5pin), 1x Allen Key, 1x Mini-USB-adapter.ZOOM SERVO DRIVE FOR ZEISS LIGHTWEIGHT ZOOM LWZ3 21-100 MM – VERSION II MOTORIZING YOUR ZEISS LWZ.3 ZOOM LENS WITH CDM-LWZ3-Z2 CONTROLLED VIA SONY FS & LANC HANDGRIP Control directly the zoom servo drive via optically de-coupled LANC sockets and Sony FS5 / FS7 handgrip zoom rocker. Other zoom rockers with LANC protocol are compatible too, e.g. mounted to handgrip. CAMERA CONTROL SIGNALS FORWARDED Control commands are immediately looped through to the camera (e.g. menu / user buttons / focus magnification / camera run & stop).SINGLE UNIT MOUNTED ONTO LENS Three captive screws keeping the single servo drive unit permanently fixed onto lens. 4 ENHANCED ZOOM MODES EB / Documentary, Live / Hardcut, Silent, and Direct ModeSingle unit mounted onto lens The CDM-LWZ3-Z2 is designed for the Zeiss Lightweight Zoom LWZ 21-100 mm/T2.9-3.9 T zoom lens (ZEISS LWZ.3). With the Zoom Servo Drive Chrosziel addresses camera operators working in the broadcast, documentary, and related sectors offering a reasonably priced device enabling creative processes that may be impossible while pulling zoom manually. The Zoom Servo Drive adds only indispensable weight to the setup. It contains one digital servo motor, the gear and a PCB with CPU in one single housing. The mounting of the Zoom Servo Drive makes the operator’s workflow comfortable. Just three captive screws are needed to mount it onto the Zeiss Lightweight Zoom (LWZ.3). Sony handgrip / other LANC handgrips with zoom rockers are working, too Zoom Servo Drive CDM-LWZ.3-Z2 with 4 enhanced zoom modes Zeiss Lightweight Zoom LWZ.3 21-100 mm/T2.9-3.9 T zoom lens (ZEISS LWZ.3) Chrosziel Light Weight Support 401-FS5 Controlled via Sony smart grip or any other LANC hand grip Until today, zoom servo drives were operated either by the inbuilt zoom rocker or external zoom devices. A second handgrip controls the camera settings or user commands. Both units are separated from each other and cannot be operated by one single hand. With the CDM-LWZ3-Z2 Chrosziel was able to unify both functionalities into one single unit. Supported are the smart grips of the Sony PXW-FS5 and Sony PXW-FS7 or any LANC compatible zoom rocker. For operation the power cable is connected and the two Jack cables with the handgrip and the camera. Once powered the zoom servo drive calibrates automatically the end stops of the lens. To further support the operator’s piece of mind Chrosziel implemented the so called “Soft Ramping”. Instead of having the zooming suddenly and unexpectedly stop, the zoom gently slows down the movement of the lens at the end stops. By using a LANC device the operator may build his or her setup, like shoulder, Steadicam or Gimbal applications. Thus, the CDM-LWZ3-Z2 makes an all-day companion for the Zeiss Lightweight Zoom LWZ.3 21-100 mm/T2.9-3.9 T zoom lens (ZEISS LWZ.3) and gives the camera operator the freedom of creativity needed. All camera control signals are forwarded Control commands (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera via the LANC protocol. By using a Sony PXW-FS5 or a Sony PXW-FS7 camera with a SWIT battery a D-Tap to a (straight or angled) Lemo compatible 5-Pin power cable is used (Chrosziel order numbers: MN-AB-A with angled Lemo compatible socket / MN-AB with straight Lemo compatible socket). The two Jack-Jack cables are forwarding the control commands from the hand grip. If e.g. a Panasonic Varicam, Sony PMW-F5 or Sony PMW-F55 are used a combined cable with power and start / stop is required, like a Hirose 4-Pin to a (straight or angled) Lemo compatible 5-Pin cable (Chrosziel order numbers: F55-A2-PCAM-A with angled Lemo socket / F55-A2-PCAM with straight Lemo compatible socket). Also, the two Jack-Jack cables are forwarding the control commands from the hand grip. Also, Chrosziel offers a variety of power cables with straight and angled plugs for all types of camera power out sockets and batteries including camera run / stop functionality (see PDF for download). LEMO compatible 0B 5-Pin socket (camera start / stop, power) 2.5 mm Jack port (control command In / Out) 3.5 mm Jack port (control command In / Out) USB type mini A-B (firmware updates) Take four: zoom servo drive zoom modes For freedom of creativity the operator may choose from four different zoom modes: EB / Documentary Mode, Live / Hardcut Mode, Silent, and Direct Mode. EB / Documentary Mode Designed for long and smooth zoom drives with the CDM-LWZ3-Z2 it offers slow creeping zoom transitions while keeping the motive perfectly framed. Silent Mode To reduce the sound of the zoom servo drive the maximum speed of its motor is limited to 40 percent making the setup almost inaudible. Live / Hardcut Mode To catch the best moments, the Live / Hardcut Mode is useful. It uses 80 percent of the maximum speed capacity of the motor offering fast zoom drives but with Soft Ramping. Direct Mode The Direct Mode finally uses the full speed capacity of the Zoom Servo Drive. The LANC commands are implemented instantaneously without ramping and smooth transitions. Useful for B camera operators catching snaps shots from the concert. How to switch zoom modes You can choose the different modes by pressing the zoom rocker for round about 25 seconds, then the green LED flashes very fast while changing the zoom mode and after that it blinks 1, 2, 3 or 4 times* – depends on the zoom mode you chose (* 1 = EB / Documentary / 2 = Silent / 3 = Live / Hard Cut / 4 = Direct). To cycle through these all you need to do is hold the zoom rocker down one way for a couple of seconds to switch to the next mode, and the other way, hold to reverse.
This website uses cookies to ensure the best experience possible. More information...