Lens Department

CDM-XK-Z2
CDM-XK-Z2 CDM-MK-Z2 - servo drive unit for Fujinon Zoom XK 20-120mm for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7) or LANC zoom devices. ZOOM SERVO DRIVE FOR FUJINON XK ZOOM LENS: CDM-XK-Z MOTORIZE YOUR FUJINON XK6X20 20-120MM T3.5 WITH CHROSZIEL SINGLE UNIT MOUNTED ONTO LENSTwo captive screws keeping the single servo drive unit permanently fixed onto lens.CONTROLLED VIA SONY FS & LANC HANDGRIPThe Sony FS5 / FS7 handgrip zoom rocker controls directly the servo drive unit. Other zoom rockers with LANC protocol are compatible too, e.g. mounted to handgrip.CAMERA CONTROL SIGNALS FORWARDEDControl signals (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera.4 ZOOM MODESEB / Documentary, Live / Hardcut, Silent, Direct Mode_________________________________________________________________All in one single housing Developed for the Fujinon XK6x20 20-120 mm zoom lens the CDM-XK-Z enables ways of creativity that may be impossible just by zooming manually. To simplify the operator’s workflow the zoom servo drive is directly mounted onto the lens by two captive screws. The weight of the CDM-XK-Z including digital motor, gear, PCB with CPU, screws and cabling is 0.44 lbs. (197 gram). With the zoom servo drive Chrosziel addresses camera operators who are working in the broadcast and documentary sector looking for a reasonably priced zoom servo drive. _____________________________________________________All camera control signals forwarded Control commands (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera via the LANC protocol. By using a Sony PXW-FS5 or a Sony PXW-FS7 camera with a SWIT battery a D-Tap to a (straight or angled) Lemo compatible 5-Pin power cable is used (Chrosziel order numbers: MN-AB-A with angled Lemo compatible socket / MN-AB with straight Lemo compatible socket). The two Jack-Jack cables are forwarding the control commands from the hand grip. If e.g. a Panasonic Varicam, Sony PMW-F5 or Sony PMW-F55 are used a combined cable with power and start / stop is required, like a Hirose 4-Pin to a (straight or angled) Lemo compatible 5-Pin cable (Chrosziel order numbers: F55-A2-PCAM-A with angled Lemo socket / F55-A2-PCAM with straight Lemo compatible socket). Also, the two Jack-Jack cables are forwarding the control commands from the hand grip. Also, Chrosziel offers a variety of power cables with straight and angled plugs for all types of camera power out sockets and batteries including camera run / stop functionality. _____________________________________________________Chrosziel CDM-XK-Z Zoom Servo Motor: zoom modes For freedom of creativity the operator may choose from four different zoom modes: EB / Documentary Mode, Live / Hardcut Mode, Silent, and Direct Mode. EB / Documentary ModeDesigned for long and smooth zoom drives with the CDM-LWZ3-Z it offers slow creeping zoom transitions while keeping the motive perfectly framed.Silent ModeTo reduce the sound of the zoom servo drive the maximum speed of its motor is limited to 40 percent making the setup almost inaudible.Live / Hardcut ModeTo catch the best moments, the Live / Hardcut Mode is useful. It uses 80 percent of the maximum speed capacity of the motor offering fast zoom drives but with Soft Ramping.Direct ModeThe Direct Mode finally uses the full speed capacity of the Zoom Servo Drive. The LANC commands are implemented instantaneously without ramping and smooth transitions. Useful for B camera operators catching snaps shots from the concert.______________________________________________________________How to change zoom modes You can choose the different modes by pressing the zoom rocker for round about 25 seconds, then the green LED flashes very fast while changing the zoom mode and after that it blinks 1, 2, 3 or 4 times* – depends on the zoom mode you chose (* 1 = EB / Documentary / 2 = Silent / 3 = Live / Hard Cut / 4 = Direct). To cycle through these all you need to do is hold the zoom rocker down one way for a couple of seconds to switch to the next mode, and the other way, hold to reverse.
Lens Test Projector TP6
Lens Test Projector TP6 Lens Test Projector TP6 - basic unit incl.: Powercable, Measuring Plane Glass, Analogue Measuring Gauge, LED-light Source (approx. 5000K), Goose-neck Orientation Lamp, Remote Control, Intergrated Digital Motor for back-focus adjustment, intergrated Lens Support, 2 Rods Ø15mm, l. 205mm, Data sheet.INCREASED PRECISION AND PERFECT DESIGN With the Chrosziel LED Lens Testing Projector TP6, the flange focal distance of your camera lenses can be professionally checked. The projector also allows a visual check of a variety of parameters that make a statement on the quality of the checked optics. Our new projector combines new, ergonomic design with a variety of new features. The proved and tested functionality of the predecessor model has been taken into account in the development of the MK6 and rendered more precisely. A variety of mounts with glass way for SD and HD, as well as for the various photographic and film lenses are available. We are happy to produce according to customer requirements. The provided remote control allows you to stay close to the projector screen at an optimum viewing distance and focus the image. Compatible with all established Lens Control Systems. FEATURESNew comfortable, ergonomic design Optimal illumination by bright LED light with 5000 K color temperature Integrated rod clamp for Ø15 mm and Ø19 mm rods New rotary switch for adjusting the dia position 2-step regulator for adjusting the light source (low/high) Plane Glass, mounted in slide holder Eclair C-Mount as base mount for all other mounts (e.g. Arri, PL, Canon, Nikon…) Low voltage orientation lamp on goose neck with XLR plug Mains supply switchable 115 / 230 volt AC Adjustment range for measurement of the back focal length: ± 1.3mm Cable-connected Remote Control