CDM-MK-Z2 - compact control-unit for Fujinon Zoom MK 18-55, 50-135mm for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7) or LANC zoom devices. Incl. 1x digital servo-motor-unit, 1x LANC cable, 1x LANC extension cable, 1 x MN-AB (powercable 12 Volt A/B D-Tap 0B 5pin), 1x Allen Key, 1x Mini-USB-adapter.DESIGNED FOR FUJINON MK 18-55MM T2.9 & FUJINON MK 50-135MM T2.9 CONTROLLED VIA SONY FS & LANC HANDGRIP Control directly the zoom servo drive via optically de-coupled LANC sockets and Sony FS5 / FS7 handgrip zoom rocker. Other zoom rockers with LANC protocol are compatible too, e.g. mounted to handgrip. CAMERA CONTROL SIGNALS FORWARDED Control signals (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera. SINGLE UNIT MOUNTED ONTO LENS Two captive screws keeping the single servo drive unit permanently fixed onto lens. 4 ZOOM MODES 1st EB / Documentary, 2nd Live / Hardcut, 3rd Silent, 4th Direct Mode

Chrosziel further expands its successful CDM Zoom Servo Drive family The FR7 zoom motor unit CDM-SFR fits seamlessly into the operating functions of the Sony PTZ ILME-FR7 camera. The FR7 Zoom Servo Drive is a compact and universal zoom motor that can be pivoted to almost any lens by simply mounting it on the 15mm rods of the Sony PTZ head. The servo drive is controlled via the Option port of the Sony ILME-FR7. The motor control can be addressed via Sony's camera-specific protocol and therefore can be used seamlessly with the whole ecosystem of the Sony FR7.Due to the included Chrosziel Flexi toothed ring (#206-30), the CDM-SFR can be used with almost any zoom lens even without standard cine gearing. This opens up a complete new range of lenses to cover the creatives needs from wide angle lenses to long-zoom operation.The FR7 Zoom servo drive unit is slid onto the 15mm rod and swiveled onto the zoom lens. The curly cables ensure safe operation within the full tilt and pan range of the Sony ILME-FR7. The tiny distribution box is mounted to the side of the FR7 base and has a built-in power input. Simply unplug the power supply of the FR7 and plug it into the distribution box. Then plug the power plug of the distribution box into the power input of the Sony FR7. Connect the RJ45 connector of the distribution box into the OPTION port of the cameras base unit (do not connect to the Ethernet port since you need this for the ILME-FR7 communication). Done.FEATURESUniversal zoom motor The CDM-SFR is a compact and universal zoom motor that can be pivoted to almost any lens by simply mounting it on the 15mm rod. Controlled via Sony ILME-FR7 The Sony ILME-FR7 base unit controls directly the servo drive unit. What ever remote panel or web access you use to control the Sony ILME-FR7, the zoom motor will receive its signal directly from the base unit of the FR7.No extra cables or power supply neededThe CDM-SFR inherits all cables, clamps, distribution box and plugs to use it right out of the box with the Sony ILME-FR7. No extra power supply needed. Technical dataPower IN 19.5V (Sony ILME-FR7 power supply used) Power OUT (Sony ILME-FR7 power plug, same voltage as power in passed through)RJ45 plug (control command In (OPTION port)) Torque 0.5Nm Power consumption max. approx. 10Wproduct code CDM-SFR EAN/GTIN number: 4250618848648 IN THE BOX 1x CDM-SFR Digital motor unit 1x 206-30 Flexi Gear Ring (Ø 60-120mm) 1x Gear Drive, mod. 0.8 (Ø 30mm)

CDM-MK-Z2 - servo drive unit for Fujinon Zoom XK 20-120mm for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7) or LANC zoom devices. ZOOM SERVO DRIVE FOR FUJINON XK ZOOM LENS: CDM-XK-Z MOTORIZE YOUR FUJINON XK6X20 20-120MM T3.5 WITH CHROSZIEL SINGLE UNIT MOUNTED ONTO LENSTwo captive screws keeping the single servo drive unit permanently fixed onto lens.CONTROLLED VIA SONY FS & LANC HANDGRIPThe Sony FS5 / FS7 handgrip zoom rocker controls directly the servo drive unit. Other zoom rockers with LANC protocol are compatible too, e.g. mounted to handgrip.CAMERA CONTROL SIGNALS FORWARDEDControl signals (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera.4 ZOOM MODESEB / Documentary, Live / Hardcut, Silent, Direct Mode_________________________________________________________________All in one single housing Developed for the Fujinon XK6x20 20-120 mm zoom lens the CDM-XK-Z enables ways of creativity that may be impossible just by zooming manually. To simplify the operator’s workflow the zoom servo drive is directly mounted onto the lens by two captive screws. The weight of the CDM-XK-Z including digital motor, gear, PCB with CPU, screws and cabling is 0.44 lbs. (197 gram). With the zoom servo drive Chrosziel addresses camera operators who are working in the broadcast and documentary sector looking for a reasonably priced zoom servo drive. _____________________________________________________All camera control signals forwarded Control commands (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera via the LANC protocol. By using a Sony PXW-FS5 or a Sony PXW-FS7 camera with a SWIT battery a D-Tap to a (straight or angled) Lemo compatible 5-Pin power cable is used (Chrosziel order numbers: MN-AB-A with angled Lemo compatible socket / MN-AB with straight Lemo compatible socket). The two Jack-Jack cables are forwarding the control commands from the hand grip. If e.g. a Panasonic Varicam, Sony PMW-F5 or Sony PMW-F55 are used a combined cable with power and start / stop is required, like a Hirose 4-Pin to a (straight or angled) Lemo compatible 5-Pin cable (Chrosziel order numbers: F55-A2-PCAM-A with angled Lemo socket / F55-A2-PCAM with straight Lemo compatible socket). Also, the two Jack-Jack cables are forwarding the control commands from the hand grip. Also, Chrosziel offers a variety of power cables with straight and angled plugs for all types of camera power out sockets and batteries including camera run / stop functionality. _____________________________________________________Chrosziel CDM-XK-Z Zoom Servo Motor: zoom modes For freedom of creativity the operator may choose from four different zoom modes: EB / Documentary Mode, Live / Hardcut Mode, Silent, and Direct Mode. EB / Documentary ModeDesigned for long and smooth zoom drives with the CDM-LWZ3-Z it offers slow creeping zoom transitions while keeping the motive perfectly framed.Silent ModeTo reduce the sound of the zoom servo drive the maximum speed of its motor is limited to 40 percent making the setup almost inaudible.Live / Hardcut ModeTo catch the best moments, the Live / Hardcut Mode is useful. It uses 80 percent of the maximum speed capacity of the motor offering fast zoom drives but with Soft Ramping.Direct ModeThe Direct Mode finally uses the full speed capacity of the Zoom Servo Drive. The LANC commands are implemented instantaneously without ramping and smooth transitions. Useful for B camera operators catching snaps shots from the concert.______________________________________________________________How to change zoom modes You can choose the different modes by pressing the zoom rocker for round about 25 seconds, then the green LED flashes very fast while changing the zoom mode and after that it blinks 1, 2, 3 or 4 times* – depends on the zoom mode you chose (* 1 = EB / Documentary / 2 = Silent / 3 = Live / Hard Cut / 4 = Direct). To cycle through these all you need to do is hold the zoom rocker down one way for a couple of seconds to switch to the next mode, and the other way, hold to reverse.

CDM-100 Chrosziel's Digital Motor, 24V operating voltage, with cable 800mm length and Lemo 7-Pin 1B standard connector.With the Digital Motor CDM-100, we developed an extremely light weight, silent, small and horizontally aligned lens motor. It perfectly suites Gimbal, Drone and SteadiCam applications.FEATURESPerfect for Gimbals, Drones and SteadiCam Horizontally aligned Extremely light weight Extremely silent Very small and short housing Motor housing with standard 19mm diameter Smart gear attachement for secure operation and fast exchange Two gear diameters (40 and 60mm), even for large lens pitches Fixed motor cable additionally reducing motor size and weight New, Universal Rod Clamp with integrated captive slider – quickly and easily adjustable for use with Ø 15mm or Ø 19mm rodsTechnical detailsDimensions: L 63 mm, max. Diameter 25 mm (without gear) Weight (without clamp): 97g without gear, ca. 110g with small gear Voltage: max. 24V Cable length: 70cm Connector Lemo 1B 7-Pin Two gears: Ø 40mm & Ø 60mm with mod 0.8 Gear Diameter Ø 40mm with mod 0.5 (CDM-D40-M05) or 0.6 (CDM-D40-M06) additionally available 15mm / 19mm Universal Rod Clamp Compatibility Chrosziel Digital Motor CDM-100 compatible with: Chrosziel MagNum, Chrosziel Aladin MK II and 3rd party brands Chrosziel Digital Motor CDM-100S compatible with: Chrosziel MagNum mini, Freefly Movi and othersIn the BoxEU15-19 Universal Rod Clamp for Ø 15/19mm CDM-D40 Gear Drivemod. 0.8, Ø 40mmCDM-D60 Gear Drivemod. 0.8, Ø 60mm

CDM-100S - Chrosziel's Digital Motor with small Lemo 7-Pin 0B connector, nominal operating voltage 24V, cable 700mm,incl.: EU15-19 Universal Rod Clamp for Ø 15/19mm, CDM-D40 Gear Drive, mod. 0.8, Ø 40mm, CDM-D60 Gear Drive, mod. 0.8, Ø 60mm, Aswell for use with Freefly Movi and others.FEATURES Digital Motor CDM-100 Perfect for Gimbals, Drones and SteadiCams Horizontally aligned Extremely light weight Very small and short housing Motor Housing with Standard 19mm Diameter Smart gear attachement for secure operation and fast exchange Two gear diameters, even for large lens pitches Fixed motor cable additionally reducing motor size and weight Universal rod clamp with captive slider for Ø 15mm / 19mm rods Technical details: Dimensions: L 63 mm, max. Diameter 25 mm (without gear) Weight (without clamp): 97g without gear, ca. 110g with small gear Voltage: max. 24V Cable length: 70cm Connector Lemo 1B 7-Pin Two gears: Ø 40mm & Ø 60mm with mod 0.8 Gear Diameter Ø 40mm with mod 0.5 (CDM-D40-M05) or 0.6 (CDM-D40-M06) additionally available 15mm / 19mm Universal Rod ClampCompatibility Chrosziel Digital Motor CDM-100 compatible with:  Chrosziel MagNum, Chrosziel Aladin MK II and 3rd party brandsChrosziel Digital Motor CDM-100S compatible with: Chrosziel MagNum mini, Freefly Movi and othersIn the BoxCDM-100S with small Lemo 7-Pin 0B connectorCable 700mmEU15-19 Universal Rod Clamp for Ø 15/19mmCDM-D40 Gear Drive, mod. 0.8, Ø 40mmCDM-D60 Gear Drive, mod. 0.8, Ø 60mm

CDM-100 Chrosziel's Digital Motor, 24V operating voltage, with cable 800mm length and Lemo 7-Pin 1B angled connector, incl.: EU15-19 Universal Rod Clamp for Ø 15/19mm, CDM-D40 Gear Drive, mod. 0.8, Ø 40mm, CDM-D60 Gear Drive, mod. 0.8, Ø 60mm.

Digital Heden Motor with digital encoder, vertical, complete w. gears module 0.8 + 0.6 + 0.5 + 0.4 and bracket for mounting to 19mm + 15mm rods

Digital Heden Motor with digital encoder, vertical, complete w. gears module 0.8 + 0.6 + 0.5 + 0.4 and bracket for mounting to 19mm + 15mm rods

CDM-100M Lens Motor Freefly MoVi Pro & MoVi XL GimbalPerfect for (focus, iris, zoom) lens controlDigital Motor CDM-100M with connector for Freefly MoVI Pro  & MoVi XL Gimbal Camera Stabilizer, 24V operating voltage, with cable 400mm length and Molex Micro-Fit 3 6pin connector plug, incl.: EU15-19 Universal Rod Clamp for Ø 15/19mm, CDM-D40 Gear Drive, mod. 0.8, Ø 40mm, CDM-D60 Gear Drive, mod. 0.8, Ø 60mm.FEATURESLIGHTWEIGHT97 grams = less than a chocolate barCOMPACT63 mm length & 19 mm diameter = small as a pinkyENERGY EFFICIENT250 mAh at 22 V = power consumption lowered by 80 %MOLEX MICROFIT 3.0Molex MicroFit 3.0 6-Pin connector = perfect for Freefly MoVi Pro gimbalLightweight, energy efficient, and versatile: Chrosziel CDM-100M This is the reason why Chrosziel is absolutely committed to designing the CDM-100M consistently for compact dimensions and weight reduction. With a length of 63 mm, a diameter of 19 mm and 97 grams, the Gimbal motor is extremely compact and lightweight. The integrated cable including the Molex MicroFit 3.0 6-pin connector saves additional weight. It can be conveniently connected to the camera stage to control focus, iris and / or zoom via the Freefly MoVi Controller, Freefly Mimic or Freefly Pilot. With a power consumption of only 250 mAh at 24 V the CDM-100M requires at least 80 percent less energy than other commercially available motors. Chrosziel supports operators of gimbal systems that require a special motor for optics in a light setup. This makes it possible to carry gimbal systems for a long time without fatigue and while saving a lot of battery power. IN THE BOX The scope of delivery includes two mod 0.8 gears with 40 and 60 mm diameter and one cable including connector. Also, included is a clamp which ensures a non-slip seat of the motor on 15 and 19 mm diameter rods through a captive reduction mechanism.

Kit Digital Motor FIZ for Freefly MoVI Pro & MoVi XL with 3x CDM-100M, each CDM-100M with connector for Freefly MoVI Pro & MoVi XL Gimbal Camera Stabilizer, 24V operating voltage, with cable 400mm length and Molex Micro-Fit 3 6pin connector plug, incl.: EU15-19 Universal Rod Clamp for Ø 15/19mm, CDM-D40 Gear Drive, mod. 0.8, Ø 40mm, CDM-D60 Gear Drive, mod. 0.8, Ø 60mm.CDM-100M LENS MOTOR FREEFLY MOVI PRO & MoVi XL GIMBAL Perfect for (focus, iris, zoom) lens control Digital Motor CDM-100M with connector for Freefly MoVI Pro & MoVi XL Gimbal Camera Stabilizer, 24V operating voltage, with cable 400mm length and Molex Micro-Fit 3 6pin connector plug, incl.: EU15-19 Universal Rod Clamp for Ø 15/19mm, CDM-D40 Gear Drive, mod. 0.8, Ø 40mm, CDM-D60 Gear Drive, mod. 0.8, Ø 60mm. FEATURESLIGHTWEIGHT 97 grams = less than a chocolate barCOMPACT63 mm length & 19 mm diameter = small as a pinkyENERGY EFFICIENT250 mAh at 22 V = power consumption lowered by 80 %MOLEX MICROFIT 3.0Molex MicroFit 3.0 6-Pin connector = perfect for Freefly MoVi Pro gimbalLIGHTWEIGHT, ENERGY EFFICIENT, AND VERSATILE: CHROSZIEL CDM-100M This is the reason why Chrosziel is absolutely committed to designing the CDM-100M consistently for compact dimensions and weight reduction. With a length of 63 mm, a diameter of 19 mm and 97 grams, the Gimbal motor is extremely compact and lightweight. The integrated cable including the Molex MicroFit 3.0 6-pin connector saves additional weight. It can be conveniently connected to the camera stage to control focus, iris and / or zoom via the Freefly MoVi Controller, Freefly Mimic or Freefly Pilot. With a power consumption of only 250 mAh at 24 V the CDM-100M requires at least 80 percent less energy than other commercially available motors. Chrosziel supports operators of gimbal systems that require a special motor for optics in a light setup. This makes it possible to carry gimbal systems for a long time without fatigue and while saving a lot of battery power. In the Box:3x CDM-100M Digital Motor FIZ for Freefly MoVI Pro, each CDM-100M with connector for Freefly MoVI Pro Gimbal Camera Stabilizer24V operating voltage, with cable 400mm length and Molex Micro-Fit 3 6pin connector plugEU15-19 Universal Rod Clamp for Ø 15/19mmCDM-D40 Gear Drive, mod. 0.8, Ø 40mmCDM-D60 Gear Drive, mod. 0.8, Ø 60mm

Y-cable for Sony FX9 - Sony Multi plug and socket to 3.5mm serial male Jack (90 degree),35cm, only for servo drives version 2

Gear Drive for Digital Motor CDM-100, mod. 0.8, Ø 60mm

Gear Drive for Digital Motor CDM-100, mod. 0.8, Ø 40mm

Gear Drive for Digital Motor CDM-100, mod. 0.5, Ø 40mm

Gear Drive for Digital Motor CDM-100, mod. 0.6, Ø 40mm

Gear Drive for Chrosziel Motor CDM-100/S/M, mod. 0.8, Ø 24mm

Gear Drive for Chrosziel Motor CDM-100/S/M, mod. 0.8, Ø 30mm

Gear Drive for Chrosziel Motor CDM-100/S/M, mod. 0.8, Ø 50mm

Gear Drive, large 24mm, for Chrosziel Motor CDM-100/S, mod. 0.8, Ø 40mm

Universal Lensport Iris Motor for cine lenses in Broadcast / ENG Run& Gun setups The universal Iris Motor is a compact and universal Iris motor that can be pivoted to almost any lens by simply mounting it on a 15mm rod. The universal motor unit CDM-LP-I fits seamlessly into the operating functions of any camera with Hirose 12pin lensport communcation. The servo drive is controlled via the 12pin Hirose output of the camera. The motor control can be addressed via the camera-specific Broadcast protocol and also works in conjunction with e.g. the MetaMount E-to-PL adapter.The Chrosziel Lensport Iris Motor now allows optimal use of all manual zoom and prime lenses together with any camera with Hirose 12pin output. For this purpose, the Iris motor is slid onto a 15mm rod and swiveled onto the zoom or prime lens. The curled Hirose 12pin cable establish the connection with the camera. Compatibility: The Universal Iris Motor has been successfully tested with the following cameras (manual and automatic iris control): ARRI Amira Blackmagic URSA Broadcast G2 & URSA Mini Pro 12K Canon C300/500 with EU-V2 expansion unit Panasonic AK-PLV100 Sony F5/F55 with LA-FZB1 adapter Sony Venice Sony E-Mount cameras with Chrosziel MetaMount MA-EPL-HR12 Manual Passive Mode: For temporary manual control, the motor can be set to passive mode. Simply press the motor button once briefly and the motor can be rotated freely. Once the button is pressed again, the motor is back in Active mode and controlled by the camera. Metadata:For setup, the cable is connected to the Hirose 12pin socket of the camera. The motor automatically calibrates itself and finds the endstops of the lens. For metadata calibration, the motor needs to learn T-Stop 4 and 16. With the press of the only button, the motor goes into passive mode and the user can turn the motor without resistance. The motor is turned to T-Stop 4 and the the press of the button confirms the position. Afterwards the motor is turned to T-Stop 16 and the position is confirmed with another press of the button. Ready! FEATURESUniversal Iris motor The Iris Motor is a compact and universal Iris motor that can be pivoted to almost any lens by simply mounting it on a 15mm rod. Controlled via any Hirose 12pin camera outputThe camera's Hirose 12pin Lensport output controls directly the Iris motor unit. Remote Iris and AutoIris controlUse the Iris motor in a remote setup and control it via the RCP or WebGUI of any camera with Hirose 12pin connector. Or switch on the AutoIris functionality of your camera and the camera uses the Chrosziel Univeral Iris Motor for AutoIris control.

The Chrosziel CDM-PREM-FIZ Full Servo Drive Unit was developed exclusively with all three Fujinon Premista Lenses and is field installable. This compact and ergonomic design allows you to integrate the all-manual “cine style“ Fujinon Premista lens into your broadcast, multi-camera and remote head workflows in a very simple way, because you have all components in one housing.Three perfectly positioned drive gears engage the Fujinon Premista lens with a high degree of precision, employing three powerful digital cine motors. The Chrosziel CDM-PREM-FIZ is particularly useful for cinematic multicam, ENG and OB work, where zoom and focus can be controlled from standard Fujinon TVstyle tripod controls or the handheld zoom rocker switch. It supports remote head and robotics applications via the Hirose 20pin Fujinon remote interface, which also allows the Chrosziel Magnum wireless FIZ unit and all other compatible brands of FIZ to control the drive’s focus, zoom and iris. This Project is supported by the Federal Ministry for Economic Affairs and Climate Action (BMWK) on the basis of a decision by the German Bundestag. TECHNICAL SPECIFICATIONS• Demand Input Focus (analog/digital 16-bit)• Demand Input Zoom (analog/digital 16-bit)• Standard Fujinon Digipower Control Protocols• External Power recommended for maximum performance• /i and eXtended data pass thru• Weight: approx. 1.2 KG (2.6 lbs)CONNECTOR OVERVIEW• Power: Lemo-compatible 0B.305• Lens-Port: 12 Pin-Hirose socket• Focus-Demand 12 Pin Hirose Socket (Fujinon standard – Pinout)• Zoom-Demand 12 Pin Hirose Socket (Fujinon standard – Pinout)• Remote (Hirose 20 Pin)KEY FEATURES• Compatible with Premista 19-45, 28-100, 80-250• /i eXtended data pass thru for augmented/ virtual production workflows• User installable drive unit• Lightweight (approx. 1.2 kg/2.6 lbs.)• Fujinon Digipower Protocols enable seamless use in robotic and remote head applications• USB Port for software updates• Wide range of power input (12V-30V DC)• Built-in adjustable speed zoom rockerWhat is in the box?• 1x CDM-PREM-FIZ – Full servo drive• 1x MN-AB-A - Power Cable 12 Volt A/B D-Tap• 1x AL2-INTF-LP – Connection Cable Lensport• 1x Allen Key

Universal Rod Clamp for Ø 15 and 19mm Rods due to integrated slider, with captive clamp lever

CDM-LWZ3-Z2 - compact control-unit for Zeiss Zoom LWZ.3 21-100mm for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7) or LANC zoom devices. Incl. 1x digital servo-motor-unit, 1x LANC cable, 1x LANC extension cable, 1 x MN-AB (powercable 12 Volt A/B D-Tap 0B 5pin), 1x Allen Key, 1x Mini-USB-adapter.ZOOM SERVO DRIVE FOR ZEISS LIGHTWEIGHT ZOOM LWZ3 21-100 MM – VERSION II MOTORIZING YOUR ZEISS LWZ.3 ZOOM LENS WITH CDM-LWZ3-Z2 CONTROLLED VIA SONY FS & LANC HANDGRIP Control directly the zoom servo drive via optically de-coupled LANC sockets and Sony FS5 / FS7 handgrip zoom rocker. Other zoom rockers with LANC protocol are compatible too, e.g. mounted to handgrip. CAMERA CONTROL SIGNALS FORWARDED Control commands are immediately looped through to the camera (e.g. menu / user buttons / focus magnification / camera run & stop).SINGLE UNIT MOUNTED ONTO LENS Three captive screws keeping the single servo drive unit permanently fixed onto lens. 4 ENHANCED ZOOM MODES EB / Documentary, Live / Hardcut, Silent, and Direct ModeSingle unit mounted onto lens The CDM-LWZ3-Z2 is designed for the Zeiss Lightweight Zoom LWZ 21-100 mm/T2.9-3.9 T zoom lens (ZEISS LWZ.3). With the Zoom Servo Drive Chrosziel addresses camera operators working in the broadcast, documentary, and related sectors offering a reasonably priced device enabling creative processes that may be impossible while pulling zoom manually. The Zoom Servo Drive adds only indispensable weight to the setup. It contains one digital servo motor, the gear and a PCB with CPU in one single housing. The mounting of the Zoom Servo Drive makes the operator’s workflow comfortable. Just three captive screws are needed to mount it onto the Zeiss Lightweight Zoom (LWZ.3). Sony handgrip / other LANC handgrips with zoom rockers are working, too Zoom Servo Drive CDM-LWZ.3-Z2 with 4 enhanced zoom modes Zeiss Lightweight Zoom LWZ.3 21-100 mm/T2.9-3.9 T zoom lens (ZEISS LWZ.3) Chrosziel Light Weight Support 401-FS5 Controlled via Sony smart grip or any other LANC hand grip Until today, zoom servo drives were operated either by the inbuilt zoom rocker or external zoom devices. A second handgrip controls the camera settings or user commands. Both units are separated from each other and cannot be operated by one single hand. With the CDM-LWZ3-Z2 Chrosziel was able to unify both functionalities into one single unit. Supported are the smart grips of the Sony PXW-FS5 and Sony PXW-FS7 or any LANC compatible zoom rocker. For operation the power cable is connected and the two Jack cables with the handgrip and the camera. Once powered the zoom servo drive calibrates automatically the end stops of the lens. To further support the operator’s piece of mind Chrosziel implemented the so called “Soft Ramping”. Instead of having the zooming suddenly and unexpectedly stop, the zoom gently slows down the movement of the lens at the end stops. By using a LANC device the operator may build his or her setup, like shoulder, Steadicam or Gimbal applications. Thus, the CDM-LWZ3-Z2 makes an all-day companion for the Zeiss Lightweight Zoom LWZ.3 21-100 mm/T2.9-3.9 T zoom lens (ZEISS LWZ.3) and gives the camera operator the freedom of creativity needed. All camera control signals are forwarded Control commands (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera via the LANC protocol. By using a Sony PXW-FS5 or a Sony PXW-FS7 camera with a SWIT battery a D-Tap to a (straight or angled) Lemo compatible 5-Pin power cable is used (Chrosziel order numbers: MN-AB-A with angled Lemo compatible socket / MN-AB with straight Lemo compatible socket). The two Jack-Jack cables are forwarding the control commands from the hand grip. If e.g. a Panasonic Varicam, Sony PMW-F5 or Sony PMW-F55 are used a combined cable with power and start / stop is required, like a Hirose 4-Pin to a (straight or angled) Lemo compatible 5-Pin cable (Chrosziel order numbers: F55-A2-PCAM-A with angled Lemo socket / F55-A2-PCAM with straight Lemo compatible socket). Also, the two Jack-Jack cables are forwarding the control commands from the hand grip. Also, Chrosziel offers a variety of power cables with straight and angled plugs for all types of camera power out sockets and batteries including camera run / stop functionality (see PDF for download). LEMO compatible 0B 5-Pin socket (camera start / stop, power) 2.5 mm Jack port (control command In / Out) 3.5 mm Jack port (control command In / Out) USB type mini A-B (firmware updates) Take four: zoom servo drive zoom modes For freedom of creativity the operator may choose from four different zoom modes: EB / Documentary Mode, Live / Hardcut Mode, Silent, and Direct Mode. EB / Documentary Mode Designed for long and smooth zoom drives with the CDM-LWZ3-Z2 it offers slow creeping zoom transitions while keeping the motive perfectly framed. Silent Mode To reduce the sound of the zoom servo drive the maximum speed of its motor is limited to 40 percent making the setup almost inaudible. Live / Hardcut Mode To catch the best moments, the Live / Hardcut Mode is useful. It uses 80 percent of the maximum speed capacity of the motor offering fast zoom drives but with Soft Ramping. Direct Mode The Direct Mode finally uses the full speed capacity of the Zoom Servo Drive. The LANC commands are implemented instantaneously without ramping and smooth transitions. Useful for B camera operators catching snaps shots from the concert. How to switch zoom modes You can choose the different modes by pressing the zoom rocker for round about 25 seconds, then the green LED flashes very fast while changing the zoom mode and after that it blinks 1, 2, 3 or 4 times* – depends on the zoom mode you chose (* 1 = EB / Documentary / 2 = Silent / 3 = Live / Hard Cut / 4 = Direct). To cycle through these all you need to do is hold the zoom rocker down one way for a couple of seconds to switch to the next mode, and the other way, hold to reverse.

CDM-EZ-Z2 - compact control-unit for Angenieux EZ-1 and EZ-2 for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7, PXW-FX9) or LANC zoom devices. Incl. 1x digital servo-motor-unit, 1x LANC cable, 1x LANC extension cable, 1x CAB-FX9 Sony Multi cable, 1 x MN-AB-A90 (powercable 12 Volt A/B D-Tap 0B 5pin angled), 1x Allen Key, 1x Mini-USBadapter.The Zoom Servo Drive 2 is a compact unit consisting of a digital motor and motor control. The Zoom Servo Drive 2 is firmly screwed to a manual cinema zoom lens and allows the zoom function of the popular large sensor cameras to be remotely controlled using the camera's multifunctional handle. This gives cameraman a larger selection of lenses with optimal operation. The Zoom Servo Drive 2 fits seamlessly into the operating functions of the Sony cameras FS7 / FS5 and FX9 / FX6 series. The Servo Drive 2 is controlled through the zoom rocker on the handle. The motor control can be addressed via the well-known LANC protocol and also works independently of the camera signals if a LANC zoom rocker is plugged directly into the servo.Internally, the Zoom Servo Drive 2 works with four different modes: documentary mode, silent mode, Live / hard cut mode and direct mode. All modes are optimized for fast or evenly slow focal length adjustment depending on the creative task. When the Servo Drive 2 is screwed to the lens, it calibrates itself to the zoom range of the lens the first time it is switched on and registers the end stops. Each zoom run is smoothly slowed down before the end stop is reached, so that it pleasantly changes into a steady state in the image. This means that the lens is not subjected to much mechanical stress. The power source of the servo is the camera battery. The servo is designed with 10-30V, suitable for use on many different camera models. Cables for the power supply are available for all existent plug connections. The Zoom Servo Drive 2 is available for each lens model for the following zoom lenses: Angenieux EZ-1 30-90mm und Angenieux EZ-2 15-40mm Fujinon MK 18-55mm and Fujinon MK 50-135mm Fujinon XK 20-120mm Zeiss LWZ.3 21-100mm