CDM-MK-Z2 - servo drive unit for Fujinon Zoom XK 20-120mm for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7) or LANC zoom devices. ZOOM SERVO DRIVE FOR FUJINON XK ZOOM LENS: CDM-XK-Z MOTORIZE YOUR FUJINON XK6X20 20-120MM T3.5 WITH CHROSZIEL SINGLE UNIT MOUNTED ONTO LENSTwo captive screws keeping the single servo drive unit permanently fixed onto lens.CONTROLLED VIA SONY FS & LANC HANDGRIPThe Sony FS5 / FS7 handgrip zoom rocker controls directly the servo drive unit. Other zoom rockers with LANC protocol are compatible too, e.g. mounted to handgrip.CAMERA CONTROL SIGNALS FORWARDEDControl signals (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera.4 ZOOM MODESEB / Documentary, Live / Hardcut, Silent, Direct Mode_________________________________________________________________All in one single housing Developed for the Fujinon XK6x20 20-120 mm zoom lens the CDM-XK-Z enables ways of creativity that may be impossible just by zooming manually. To simplify the operator’s workflow the zoom servo drive is directly mounted onto the lens by two captive screws. The weight of the CDM-XK-Z including digital motor, gear, PCB with CPU, screws and cabling is 0.44 lbs. (197 gram). With the zoom servo drive Chrosziel addresses camera operators who are working in the broadcast and documentary sector looking for a reasonably priced zoom servo drive. _____________________________________________________All camera control signals forwarded Control commands (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera via the LANC protocol. By using a Sony PXW-FS5 or a Sony PXW-FS7 camera with a SWIT battery a D-Tap to a (straight or angled) Lemo compatible 5-Pin power cable is used (Chrosziel order numbers: MN-AB-A with angled Lemo compatible socket / MN-AB with straight Lemo compatible socket). The two Jack-Jack cables are forwarding the control commands from the hand grip. If e.g. a Panasonic Varicam, Sony PMW-F5 or Sony PMW-F55 are used a combined cable with power and start / stop is required, like a Hirose 4-Pin to a (straight or angled) Lemo compatible 5-Pin cable (Chrosziel order numbers: F55-A2-PCAM-A with angled Lemo socket / F55-A2-PCAM with straight Lemo compatible socket). Also, the two Jack-Jack cables are forwarding the control commands from the hand grip. Also, Chrosziel offers a variety of power cables with straight and angled plugs for all types of camera power out sockets and batteries including camera run / stop functionality. _____________________________________________________Chrosziel CDM-XK-Z Zoom Servo Motor: zoom modes For freedom of creativity the operator may choose from four different zoom modes: EB / Documentary Mode, Live / Hardcut Mode, Silent, and Direct Mode. EB / Documentary ModeDesigned for long and smooth zoom drives with the CDM-LWZ3-Z it offers slow creeping zoom transitions while keeping the motive perfectly framed.Silent ModeTo reduce the sound of the zoom servo drive the maximum speed of its motor is limited to 40 percent making the setup almost inaudible.Live / Hardcut ModeTo catch the best moments, the Live / Hardcut Mode is useful. It uses 80 percent of the maximum speed capacity of the motor offering fast zoom drives but with Soft Ramping.Direct ModeThe Direct Mode finally uses the full speed capacity of the Zoom Servo Drive. The LANC commands are implemented instantaneously without ramping and smooth transitions. Useful for B camera operators catching snaps shots from the concert.______________________________________________________________How to change zoom modes You can choose the different modes by pressing the zoom rocker for round about 25 seconds, then the green LED flashes very fast while changing the zoom mode and after that it blinks 1, 2, 3 or 4 times* – depends on the zoom mode you chose (* 1 = EB / Documentary / 2 = Silent / 3 = Live / Hard Cut / 4 = Direct). To cycle through these all you need to do is hold the zoom rocker down one way for a couple of seconds to switch to the next mode, and the other way, hold to reverse.

CDM-MK-Z2 - compact control-unit for Fujinon Zoom MK 18-55, 50-135mm for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7) or LANC zoom devices. Incl. 1x digital servo-motor-unit, 1x LANC cable, 1x LANC extension cable, 1 x MN-AB (powercable 12 Volt A/B D-Tap 0B 5pin), 1x Allen Key, 1x Mini-USB-adapter.DESIGNED FOR FUJINON MK 18-55MM T2.9 & FUJINON MK 50-135MM T2.9 CONTROLLED VIA SONY FS & LANC HANDGRIP Control directly the zoom servo drive via optically de-coupled LANC sockets and Sony FS5 / FS7 handgrip zoom rocker. Other zoom rockers with LANC protocol are compatible too, e.g. mounted to handgrip. CAMERA CONTROL SIGNALS FORWARDED Control signals (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera. SINGLE UNIT MOUNTED ONTO LENS Two captive screws keeping the single servo drive unit permanently fixed onto lens. 4 ZOOM MODES 1st EB / Documentary, 2nd Live / Hardcut, 3rd Silent, 4th Direct Mode

Universal Lensport Iris Motor for cine lenses in Broadcast / ENG Run& Gun setups The universal Iris Motor is a compact and universal Iris motor that can be pivoted to almost any lens by simply mounting it on a 15mm rod. The universal motor unit CDM-LP-I fits seamlessly into the operating functions of any camera with Hirose 12pin lensport communcation. The servo drive is controlled via the 12pin Hirose output of the camera. The motor control can be addressed via the camera-specific Broadcast protocol and also works in conjunction with e.g. the MetaMount E-to-PL adapter.The Chrosziel Lensport Iris Motor now allows optimal use of all manual zoom and prime lenses together with any camera with Hirose 12pin output. For this purpose, the Iris motor is slid onto a 15mm rod and swiveled onto the zoom or prime lens. The curled Hirose 12pin cable establish the connection with the camera. Compatibility: The Universal Iris Motor has been successfully tested with the following cameras (manual and automatic iris control): ARRI Amira Blackmagic URSA Broadcast G2 & URSA Mini Pro 12K Canon C300/500 with EU-V2 expansion unit Panasonic AK-PLV100 Sony F5/F55 with LA-FZB1 adapter Sony Venice Sony E-Mount cameras with Chrosziel MetaMount MA-EPL-HR12 Manual Passive Mode: For temporary manual control, the motor can be set to passive mode. Simply press the motor button once briefly and the motor can be rotated freely. Once the button is pressed again, the motor is back in Active mode and controlled by the camera. Metadata:For setup, the cable is connected to the Hirose 12pin socket of the camera. The motor automatically calibrates itself and finds the endstops of the lens. For metadata calibration, the motor needs to learn T-Stop 4 and 16. With the press of the only button, the motor goes into passive mode and the user can turn the motor without resistance. The motor is turned to T-Stop 4 and the the press of the button confirms the position. Afterwards the motor is turned to T-Stop 16 and the position is confirmed with another press of the button. Ready! FEATURESUniversal Iris motor The Iris Motor is a compact and universal Iris motor that can be pivoted to almost any lens by simply mounting it on a 15mm rod. Controlled via any Hirose 12pin camera outputThe camera's Hirose 12pin Lensport output controls directly the Iris motor unit. Remote Iris and AutoIris controlUse the Iris motor in a remote setup and control it via the RCP or WebGUI of any camera with Hirose 12pin connector. Or switch on the AutoIris functionality of your camera and the camera uses the Chrosziel Univeral Iris Motor for AutoIris control.

Chrosziel further expands its successful CDM Zoom Servo Drive family The FR7 zoom motor unit CDM-SFR fits seamlessly into the operating functions of the Sony PTZ ILME-FR7 camera. The FR7 Zoom Servo Drive is a compact and universal zoom motor that can be pivoted to almost any lens by simply mounting it on the 15mm rods of the Sony PTZ head. The servo drive is controlled via the Option port of the Sony ILME-FR7. The motor control can be addressed via Sony's camera-specific protocol and therefore can be used seamlessly with the whole ecosystem of the Sony FR7.Due to the included Chrosziel Flexi toothed ring (#206-30), the CDM-SFR can be used with almost any zoom lens even without standard cine gearing. This opens up a complete new range of lenses to cover the creatives needs from wide angle lenses to long-zoom operation.The FR7 Zoom servo drive unit is slid onto the 15mm rod and swiveled onto the zoom lens. The curly cables ensure safe operation within the full tilt and pan range of the Sony ILME-FR7. The tiny distribution box is mounted to the side of the FR7 base and has a built-in power input. Simply unplug the power supply of the FR7 and plug it into the distribution box. Then plug the power plug of the distribution box into the power input of the Sony FR7. Connect the RJ45 connector of the distribution box into the OPTION port of the cameras base unit (do not connect to the Ethernet port since you need this for the ILME-FR7 communication). Done.FEATURESUniversal zoom motor The CDM-SFR is a compact and universal zoom motor that can be pivoted to almost any lens by simply mounting it on the 15mm rod. Controlled via Sony ILME-FR7 The Sony ILME-FR7 base unit controls directly the servo drive unit. What ever remote panel or web access you use to control the Sony ILME-FR7, the zoom motor will receive its signal directly from the base unit of the FR7.No extra cables or power supply neededThe CDM-SFR inherits all cables, clamps, distribution box and plugs to use it right out of the box with the Sony ILME-FR7. No extra power supply needed. Technical dataPower IN 19.5V (Sony ILME-FR7 power supply used) Power OUT (Sony ILME-FR7 power plug, same voltage as power in passed through)RJ45 plug (control command In (OPTION port)) Torque 0.5Nm Power consumption max. approx. 10Wproduct code CDM-SFR EAN/GTIN number: 4250618848648 IN THE BOX 1x CDM-SFR Digital motor unit 1x 206-30 Flexi Gear Ring (Ø 60-120mm) 1x Gear Drive, mod. 0.8 (Ø 30mm)

CDM-LWZ3-Z2 - compact control-unit for Zeiss Zoom LWZ.3 21-100mm for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7) or LANC zoom devices. Incl. 1x digital servo-motor-unit, 1x LANC cable, 1x LANC extension cable, 1 x MN-AB (powercable 12 Volt A/B D-Tap 0B 5pin), 1x Allen Key, 1x Mini-USB-adapter.ZOOM SERVO DRIVE FOR ZEISS LIGHTWEIGHT ZOOM LWZ3 21-100 MM – VERSION II MOTORIZING YOUR ZEISS LWZ.3 ZOOM LENS WITH CDM-LWZ3-Z2 CONTROLLED VIA SONY FS & LANC HANDGRIP Control directly the zoom servo drive via optically de-coupled LANC sockets and Sony FS5 / FS7 handgrip zoom rocker. Other zoom rockers with LANC protocol are compatible too, e.g. mounted to handgrip. CAMERA CONTROL SIGNALS FORWARDED Control commands are immediately looped through to the camera (e.g. menu / user buttons / focus magnification / camera run & stop).SINGLE UNIT MOUNTED ONTO LENS Three captive screws keeping the single servo drive unit permanently fixed onto lens. 4 ENHANCED ZOOM MODES EB / Documentary, Live / Hardcut, Silent, and Direct ModeSingle unit mounted onto lens The CDM-LWZ3-Z2 is designed for the Zeiss Lightweight Zoom LWZ 21-100 mm/T2.9-3.9 T zoom lens (ZEISS LWZ.3). With the Zoom Servo Drive Chrosziel addresses camera operators working in the broadcast, documentary, and related sectors offering a reasonably priced device enabling creative processes that may be impossible while pulling zoom manually. The Zoom Servo Drive adds only indispensable weight to the setup. It contains one digital servo motor, the gear and a PCB with CPU in one single housing. The mounting of the Zoom Servo Drive makes the operator’s workflow comfortable. Just three captive screws are needed to mount it onto the Zeiss Lightweight Zoom (LWZ.3). Sony handgrip / other LANC handgrips with zoom rockers are working, too Zoom Servo Drive CDM-LWZ.3-Z2 with 4 enhanced zoom modes Zeiss Lightweight Zoom LWZ.3 21-100 mm/T2.9-3.9 T zoom lens (ZEISS LWZ.3) Chrosziel Light Weight Support 401-FS5 Controlled via Sony smart grip or any other LANC hand grip Until today, zoom servo drives were operated either by the inbuilt zoom rocker or external zoom devices. A second handgrip controls the camera settings or user commands. Both units are separated from each other and cannot be operated by one single hand. With the CDM-LWZ3-Z2 Chrosziel was able to unify both functionalities into one single unit. Supported are the smart grips of the Sony PXW-FS5 and Sony PXW-FS7 or any LANC compatible zoom rocker. For operation the power cable is connected and the two Jack cables with the handgrip and the camera. Once powered the zoom servo drive calibrates automatically the end stops of the lens. To further support the operator’s piece of mind Chrosziel implemented the so called “Soft Ramping”. Instead of having the zooming suddenly and unexpectedly stop, the zoom gently slows down the movement of the lens at the end stops. By using a LANC device the operator may build his or her setup, like shoulder, Steadicam or Gimbal applications. Thus, the CDM-LWZ3-Z2 makes an all-day companion for the Zeiss Lightweight Zoom LWZ.3 21-100 mm/T2.9-3.9 T zoom lens (ZEISS LWZ.3) and gives the camera operator the freedom of creativity needed. All camera control signals are forwarded Control commands (e.g. menu / user buttons / focus magnification / camera run & stop) are immediately looped through to the camera via the LANC protocol. By using a Sony PXW-FS5 or a Sony PXW-FS7 camera with a SWIT battery a D-Tap to a (straight or angled) Lemo compatible 5-Pin power cable is used (Chrosziel order numbers: MN-AB-A with angled Lemo compatible socket / MN-AB with straight Lemo compatible socket). The two Jack-Jack cables are forwarding the control commands from the hand grip. If e.g. a Panasonic Varicam, Sony PMW-F5 or Sony PMW-F55 are used a combined cable with power and start / stop is required, like a Hirose 4-Pin to a (straight or angled) Lemo compatible 5-Pin cable (Chrosziel order numbers: F55-A2-PCAM-A with angled Lemo socket / F55-A2-PCAM with straight Lemo compatible socket). Also, the two Jack-Jack cables are forwarding the control commands from the hand grip. Also, Chrosziel offers a variety of power cables with straight and angled plugs for all types of camera power out sockets and batteries including camera run / stop functionality (see PDF for download). LEMO compatible 0B 5-Pin socket (camera start / stop, power) 2.5 mm Jack port (control command In / Out) 3.5 mm Jack port (control command In / Out) USB type mini A-B (firmware updates) Take four: zoom servo drive zoom modes For freedom of creativity the operator may choose from four different zoom modes: EB / Documentary Mode, Live / Hardcut Mode, Silent, and Direct Mode. EB / Documentary Mode Designed for long and smooth zoom drives with the CDM-LWZ3-Z2 it offers slow creeping zoom transitions while keeping the motive perfectly framed. Silent Mode To reduce the sound of the zoom servo drive the maximum speed of its motor is limited to 40 percent making the setup almost inaudible. Live / Hardcut Mode To catch the best moments, the Live / Hardcut Mode is useful. It uses 80 percent of the maximum speed capacity of the motor offering fast zoom drives but with Soft Ramping. Direct Mode The Direct Mode finally uses the full speed capacity of the Zoom Servo Drive. The LANC commands are implemented instantaneously without ramping and smooth transitions. Useful for B camera operators catching snaps shots from the concert. How to switch zoom modes You can choose the different modes by pressing the zoom rocker for round about 25 seconds, then the green LED flashes very fast while changing the zoom mode and after that it blinks 1, 2, 3 or 4 times* – depends on the zoom mode you chose (* 1 = EB / Documentary / 2 = Silent / 3 = Live / Hard Cut / 4 = Direct). To cycle through these all you need to do is hold the zoom rocker down one way for a couple of seconds to switch to the next mode, and the other way, hold to reverse.

Chrosziel has expanded the successful CDM Zoom Servo Drive family. The Zoomer is a compact and universal zoom motor that can be pivoted to almost any lens by simply mounting it on a 15mm rod. The universal motor unit CDM-UNI-Z2 fits seamlessly into the operating functions of the Sony cameras of the FX9 / FX6 / FS7 / FS5 series. The servo drive is controlled via the zoom rocker on the handle. The motor control can be addressed via Sony's camera-specific protocol and also works independently of the camera signals when a digital LANC zoom rocker is plugged directly into the servo.Due to the included Chrosziel Flexi toothed ring (#206-30), the Zoomer can be used with almost any zoom lens even without standard cine gearing. The multi-function handgrip, which in addition to the recording function and a zoom rocker also provide control over the camera menu and other freely selectable functions, are extremely popular on current video cameras with large sensors and are indispensable for effective operation. The Chrosziel Universal Zoom Servo Drive now allows optimal use of all manual zoom lenses together with the multi-function handgrip. For this purpose, the Zoomer is slid onto a 15mm rod and swiveled onto the zoom lens. Two plug-in cables establish the connection with the camera. One cable is used for the power supply from the camera battery, the second for the connection to the control commands between the handle and the camera. When using a standard LANC zoom rocker or handle with the Sony PXW-FS5, PXW-FS7 and PXW-FS7II, the servo is connected between the handle and the camera via an input and an output jack to receive all zoom control signals. For setup with the Sony PXW-FX9 camera, a Y-cable is used that accepts the Sony multi-connector and connects to both the input jack of the Zoomer and the input jack of the camera. For the Sony ILME-FX6 camera, a Y-cable is used and connects the 3.5mm connector of the Sony handgrip, input jack of the Universal Zoom Servo Drive, and the Sony camera.  FEATURESUniversal zoom motor The Zoomer is a compact and universal zoom motor that can be pivoted to almost any lens by simply mounting it on a 15mm rod. Controlled via Sony and Digtial LANC handgrip The Sony FX6 / FX9 / FS5 / FS7 handgrip zoom rocker controls directly the servo drive unit. Other zoom rockers with digital LANC protocol are compatible too, e.g. mounted handgrip. Camera control signals forwarded Control commands are immediately looped through to the camera (e.g. menu / user buttons / focus magnification / camera run & stop). Panasonic DC-BS1H & DC-BGH1 box cameras A recent firmware updated has made the CDM-UNI-Z2 compatible with the Panasonic BS1H and BGH-1 box cinema cameras when used with a Manfrotto MVR901EPLA and MVR901ECLA control handles as well as the digital LANC Libec ZFC-L and ZC-LP zoom controllers. Technical dataPower supply 10-30V (Lemo compatible 0B 5-pin) 2.5mm socket (control command In) 3.5mm socket (control command In&Out)USB Type min A-B (firmware updates) Torque 0.5Nm Power consumption max. approx. 350mAh @ 12VIN THE BOX 1x CDM-UNI-Z2 Digital motor unit 1x LANC cable 1x LANC extension cable 1x MN-AB-A90 (power supply cable 12 Volt A/B D-Tap – angled 90° rotated 0B 5pin) 1x 206-30 Flexi Gear Ring (Ø 60-120mm) 1x Gear Drive, mod. 0.8 (Ø 40mm) 1x CAB-FX9 for Sony PXW-FX9 compatibility 1x CAB-FX6 for Sony PXW-FX6 compatibility USB Mini AdapterSign up for ZOOMER email updatesDon't miss future news about the ZOOMER and subscribe to the Zoomer Email list. Yes, keep me updated about the ZOOMER and send me future news about it.NOTE: we will not use your email for any other emails not related to the Zoomer. hbspt.forms.create({ region: "na1", portalId: "2769585", formId: "aae38178-6132-4e21-b6b4-bd9ac7e2828f" });

CDM-EZ-Z2 - compact control-unit for Angenieux EZ-1 and EZ-2 for controlling zoom. For usage with orig. Sony handgrip (PXW-FS5, PXW-FS7, PXW-FX9) or LANC zoom devices. Incl. 1x digital servo-motor-unit, 1x LANC cable, 1x LANC extension cable, 1x CAB-FX9 Sony Multi cable, 1 x MN-AB-A90 (powercable 12 Volt A/B D-Tap 0B 5pin angled), 1x Allen Key, 1x Mini-USBadapter.The Zoom Servo Drive 2 is a compact unit consisting of a digital motor and motor control. The Zoom Servo Drive 2 is firmly screwed to a manual cinema zoom lens and allows the zoom function of the popular large sensor cameras to be remotely controlled using the camera's multifunctional handle. This gives cameraman a larger selection of lenses with optimal operation. The Zoom Servo Drive 2 fits seamlessly into the operating functions of the Sony cameras FS7 / FS5 and FX9 / FX6 series. The Servo Drive 2 is controlled through the zoom rocker on the handle. The motor control can be addressed via the well-known LANC protocol and also works independently of the camera signals if a LANC zoom rocker is plugged directly into the servo.Internally, the Zoom Servo Drive 2 works with four different modes: documentary mode, silent mode, Live / hard cut mode and direct mode. All modes are optimized for fast or evenly slow focal length adjustment depending on the creative task. When the Servo Drive 2 is screwed to the lens, it calibrates itself to the zoom range of the lens the first time it is switched on and registers the end stops. Each zoom run is smoothly slowed down before the end stop is reached, so that it pleasantly changes into a steady state in the image. This means that the lens is not subjected to much mechanical stress. The power source of the servo is the camera battery. The servo is designed with 10-30V, suitable for use on many different camera models. Cables for the power supply are available for all existent plug connections. The Zoom Servo Drive 2 is available for each lens model for the following zoom lenses: Angenieux EZ-1 30-90mm und Angenieux EZ-2 15-40mm Fujinon MK 18-55mm and Fujinon MK 50-135mm Fujinon XK 20-120mm Zeiss LWZ.3 21-100mm

401-BUR-ADV-KIT: THE COMPLETE LWS CAGE FOR THE SONY BURANOThe Chrosziel Advance Cage Kit fitted for the Sony Burano is a slim, lightweight yet sturdy cage that allows access to all camera controls and ports while adding dozens of mounting points for essential gear and accessories the camera needs for filming. The Advanced cage kit is perfect for run-n-gun shooting, live event broadcasting or tripod mounted studio work.  Fitted LWS Baseplate with VCT mount, shoulder pad and 15mm rod mounts, a pair of 20 cm rods in is included Top-Plate for Sony Burano, built-in Ø15mm rod attachment, with integrated mounting points and a pair of 9cm rods included. Top plate has removeable center so FX9 handle with built in electronics can be used Right and Left front side brackets with more mounting points Rear right side bracket that secures to the top plate and the camera with 2 extra screws to support heavier accessories The 401-BUR-ADV-KIT Chorsziel Cage Consists of: 1x 401-VEN  LWS base plate with integrated shoulder pad 1x 401-BUR-TOP  Top plate with 15mm rods 1x 401-BUR-SBF  Front side bracket right 1x 401-BUR-SBL Front side bracket Left 1x 401-BUR-SBR  Rear side bracket 

401-BUR-STD-KIT: THE LWS RUN-N-GUN CAGE FOR THE SONY BURANOThe Chrosziel Standard Cage Kit fitted for the Sony Burano is a slim, lightweight yet sturdy cage that allows access to all camera controls and ports while adding dozens of mounting points for essential gear and accessories the camera needs for filming. The Advanced cage kit is perfect for run-n-gun shooting, live event broadcasting hand-held or tripod mounted.  Fitted LWS Baseplate with VCT mount, shoulder pad and 15mm rod mounts, a pair of 20 cm rods in is included Top-Plate for Sony Burano, built-in Ø15mm rod attachment, with integrated mounting points and a pair of 9cm rods included. Top plate has removeable center so FX9 handle with built in electronics can be used  The 401-BUR-ADV-KIT Chorsziel Cage Consists of: 1x 401-VEN  LWS base plate with integrated shoulder pad 1x 401-BUR-TOP  Top plate with 15mm rods 

Chrosziel Front-Side-Bracket for Sony Burano, with integrated mounting points 1/4" and 3/8". The front-side-plate is attached to the Chrosziel top plate (401-BUR-TOP) and to the light weight support (401-VEN) or bridge plate (401-VEN-BRI).401-BUR-SBF: THE SONY Burano Front Side BracketThe Front Side Bracket comes with numerous 3/8″ & 1/4″ fastening points with ARRI anti-twist safeguard. It is mounted with two screws into the Chrosziel 401-BUR-TOP top plate and additionally into the two threading of the Chrosziel Light Weight Support 401-VEN or Chrosziel Bridge Plate 401-VEN-BRI. Front Side Bracket for Sony Burano, with integrated mounting points 1/4" and 3/8" threads mounted on the Chrosziel 401-BUR-TOP top plate and the two threading of the Chrosziel 401-VEN or 401-VEN-BRI

Chrosziel Top-Plate for Sony Burano, built-in Ø15mm rod support, with integrated mounting points 1/4" and 3/8", pair of Ø15mm rods - 9cm / 3.55inch with internal thread (extendable). The top-plate is split into two parts allowing the use of either the standard Sony Burano Top Handle or the Sony FX9 Top Handle with built-in electronics for maximum Run&Gun shooting.401-BUR-TOP: THE CHERRY ON THE SONY Burano “CAKE”The Top Plate comes with rod support in standard optical height, numerous 3/8″ & 1/4″ fastening points with ARRI anti-twist safeguard and an optical marker for attaching a measuring tape. Additionally the top plate inherits various mounting points to move the Sony Burano cable clamps to the desired position. Top-Plate for Sony Burano, built-in Ø15mm rod attachment, with integrated mounting points 1/4" and 3/8", pair of Ø15mm rods - 9cm /3.55inch with internal thread (extendable) top-plate split into two parts for the standard Sony Burano Top Handle or the Sony FX9 Top Handle with built-in electronics

Top-Plate for Sony Venice 2, Ø15mm rod attachment, with integrated mounting points 1/4" and 3/8", pair of Ø15mm rods - 9cm / 3.55inch with internal thread (extendable).401-VEN-TOP: THE CHERRY ON THE SONY Venice 2 “CAKE”The Top Plate comes with rod support in standard optical height, numerous 3/8″ & 1/4″ fastening points with ARRI anti-twist safeguard and an optical marker for attaching a measuring tape. Top-Plate for Sony Venice 2, Ø15mm rod attachment, with integrated mounting points 1/4" and 3/8", pair of Ø15mm rods - 9cm /3.55inch with internal thread (extendable)

Chrosziel Rear-Side-Bracket for Sony Burano, with integrated mounting points 1/4" and 3/8". The rear-side-plate is attached to the Chrosziel top plate (401-BUR-TOP) and to the body-owned two threadings.401-BUR-SBR: THE SONY Burano Rear Side BracketThe Rear Side Bracket comes with numerous 3/8″ & 1/4″ fastening points with ARRI anti-twist safeguard. It is mounted with two screws into the Chrosziel 401-BUR-TOP top plate and additionally into the two threading of the Sony Burano camera body. Rear Side Bracket for Sony Burano, with integrated mounting points 1/4" and 3/8" threads mounted on the Chrosziel 401-BUR-TOP top plate and the two threading of the Sony Burano camera body

Top-Plate for Sony PXW-FX9, Ø15mm rod attachment, with integrated mounting points 1/4" and 3/8", pair of Ø15mm rods - 9cm / 3.55inch with internal thread (extendable).401-FX9-TOP: THE CHERRY ON THE SONY PXW-FX9 “CAKE”The Top Plate comes with rod support in standard optical height, numerous 3/8″ & 1/4″ fastening points with ARRI anti-twist safeguard, recess for further use of the electronic FX9 handle and an optical marker for attaching a measuring tape. Top-Plate for Sony PXW-FX9, Ø15mm rod attachment, with integrated mounting points 1/4" and 3/8", pair of Ø15mm rods - 9cm /3.55inch with internal thread (extendable)

Light weight support for Sony PXW-FX9, with integrated shoulder pad, 2 rosettes, V- Lock-Plate, 401-FS7/5-03 Tripod Adapter Plate2 rods Ø 15mm, l. 205mm.LIGHTWEIGHT SUPPORT (LWS) FOR SONY FX9 CAMERAS  Features of the LightWeight Support 401-FX9: new comfortable ergonomic soft shoulder pad, two rosette (right and left), numerous 3/8″ & 1/4″ fastening points incl. ARRI anti-twist safeguard, compatibility to QuickRelease and tripod adapter plates and optional rear rod support.The LightWeight Support can be modularly used with industry standard QuickLock Plates. The Chrosziel QuickLock Plate 401-150 is suitable for all cameras which are equipped with wedge plate connections (V mount) in the front and a mounting bracket behind the shoulder support. The QuickLock Plate connects the camera quickly and easily, and even after decades of use. LIGHT AS A FEATHER: THE SHOULDER PAD OF THE 401-FX9 LIGHTWEIGHT SUPPORT The shoulder pad under the light support can be moved over a wide range. A lever clamp mechanism with external lever access allows the user to slide it on the shoulder. This allows him to quickly correct the balance of the camera during operation. The pad is tapered to fit the shoulder and has an elevation toward the neck for side protection. After fully opening the lever clamp, the pad can be removed and inserted rotated 180 degrees, so that one can equally use the light support on the left or right shoulder. The pad itself is manufactured using a new process from the automotive industry in a special mold with a molded core surrounded by an elastic material with a strong durable outer shell. This multi-layer construction results in high comfort and fatigue-free work.User feedback played a key role while designing the LightWeight Support 401-FX9.The result is a completely re-design of the shoulder pad:Use of a two component cushioning material Shoulder pad adapts to the physical conditions when under pressure Shoulder pad is adjustable (forward and backward) FITS PERFECTLY Secure hold with tripod adpter plate 401-FS7/5-03The standard scope of delivery of the LightWeight Support 401-FX9 consists of a tripod adapter plate 401-FS7/5-03. With the tripod adapter plate the lightweight support can be directly and securely mounted to a tripod without a VCT QuickLock Plate (universal plate). It is just necessary to replace the pre-assembled V Lock by the tripod adapter plate.CLAMPS ONLY WHEN NEEDED: REAR ROD CLAMP FOR 15 MM RODS Useful add-on to the Sony PXW-FX9 setupTo expand the Sony PWX-FX9 setup with battery packs, break out boxes etc. Chrosziel offers a rear rod clamp für the LWS 401-FX9. Only one screw is needed to easily mount the rear rod clamp to the lightweight support. It offers two 15 mm rod insertions that can be comfortably fixed by a locking screw.IN THE BOX 2 rosettes V-Lock-Plate 401-FS7/5-03 Tripod Adapter Plate 2 rods Ø 15mm length: 205mm